background image

12

6.1 heAlth And SAFety recoMMendAtionS

Warnings for the use of Wireless Devices

: Please observe all warning notices with regard to 

the usage of wireless devices

Potentially Hazardous Atmospheres: 

You are reminded of the need to observe restrictions 

on the use of radio devices in fuel depots, chemical plants etc. and areas where the air con-
tains chemicals or particles (such as grain, dust, or metal powders). 

Safety in Hospitals

: Wireless devices transmit radio frequency energy and may affect medical 

electrical equipment. When installed adjacent to other equipment, it is advised to verify that 
the adjacent equipment is not adversely affected.

Power Supply:

 Use only a Motorola approved power supply for the AP-PSBIAS-5181-01R POE 

injector output rated at 48VDC and 500mA. Refer to the Motorola AP-PSBIAS-5181-01R POE 
injector documentation for installation instruction and operational guidelines.

6.2 rF exPoSure guidelineS

Safety Information:

 The device complies with internationally recognized standards covering 

human exposure to electromagnetic fields from radio devices.

Warning: Exposure To Radio Frequency (RF) Radiation

•  The radiated output of this device is below the FCC radio frequency exposure limits. 

Nevertheless, the device should be used in such a manner that the potential for human 
contact during normal operation is minimized.

•  The end user must avoid any extended human RF exposure directly in front of the Model 

SWM-1000-O, up to a distance of 20cm, when unit is switched on.

•  When servicing the equipment and selecting a location for the antennas, it is important 

to note that a minimum distance of 20cm is required between personnel and the Model 
SWM-1000-O antennas to comply with the radio frequency exposure limit.

•  The antenna used for this transmitter must be installed to provide a separation distance 

of at least 20cm from all persons and must not be co-located or operating in conjunction 
with any other antenna or transmitter.

•  The following safety precautions should be observed:

 

− Do not touch or move the antenna while the unit is transmitting or receiving.

 

− Do not hold any component containing the radio such that the antenna is very close or 

touching any exposed parts of the body, especially the face or eyes, while transmitting.

 

− Do not operate the radio or attempt to transmit data unless the antenna is connected; 

this behavior may cause damage to the radio.

Summary of Contents for SWM-1000-O

















Reviews: