manualshive.com logo in svg

Lutron Electronics WC-2M-GC, Installer'S Manual, Page: 14 / 16

Share
Download
Lutron Electronics WC-2M-GC Installer'S Manual Download Page 14

14

AC motor does not move in either
direction when manual override
buttons pressed.

• Motor wired to Group Controller

improperly.

• Limit switches on motor not set

properly.

• Motor Supply Jumper terminal is not

jumpered to 120 V terminal.

Verify motor wiring.

Verify limit switch settings on motor.

Place a jumper wire of sufficient wire
gauge between Motor Supply Jumper
and 120 V Input Voltage terminals.
See page 6.

Troubleshooting

Motors cannot be controlled from low-
voltage contact closure inputs but
operate properly with the manual
Open/Close buttons.

• Contact closure miswire.

Verify connections on contact closure
inputs.

Motors only move while low-voltage
contact closure is applied.

• Options Switch #5 in ON position.

Change position of Options Switch #5
to OFF. See page 11.

Motor moves in the wrong direction.

• Options Switch not set properly.

Reverse the corresponding Options
Switch. See page 7.

Symptom

Possible Cause

Solution

Summary of Contents for WC-2M-GC

















Reviews:

No comments