Lutron Electronics VIMCO SIVOIA SV-MDU-20-KIT Installation & Operating Instructions Manual Download Page 6

Page: 6 / 16

Page 6

ATTACH MDU and IDLER SUPPORT

Attach the idler support to the mounting bracket
using three (3) truss-head screws.

Attach the MDU to the mounting bracket using three
(3) truss-head screws.

HANGING THE SHADE

Unwrap approximately 1 ft. (0.3 m) of material and insert the edge of the material between the guide posts of the home
position reset lever.

Attach the shade to the MDU first by engaging the roller’s hexagonal socket with the motor’s hexagonal drive ball. You
may need to rotate the roller in order to push the shade over the hexagonal drive ball.

Insert the idler pin into the upper slot of the idler support and drop it into place.

Home Position

Reset Lever

Summary of Contents for VIMCO SIVOIA SV-MDU-20-KIT

















Search results

Summary of Contents for VIMCO SIVOIA SV-MDU-20-KIT

Reviews:

Related manuals for VIMCO SIVOIA SV-MDU-20-KIT

Brands by name

Popular brands

Lutron Electronics VIMCO SIVOIA SV-MDU-20-KIT, Installation & Operating Instructions Manual

Search results

Summary of Contents for VIMCO SIVOIA SV-MDU-20-KIT

Reviews:

Related manuals for VIMCO SIVOIA SV-MDU-20-KIT

Brands by name

Popular brands