Lutron Electronics VIMCO SIVOIA SV-MDU-20-KIT Installation & Operating Instructions Manual Download Page 5

Page: 5 / 16

Page 5

FASTEN MOUNTING BRACKETS (CONT’D)

For Ceiling-Mount Applications...

Follow steps A & B from the previous page, then line up and fasten the brackets as shown.

Note:

Make sure the opening of the ceiling bracket faces outward towards the room.

Fabric Edge

Wall

Ceiling

Bracket

Top View

5”

(127mm)

Line up this bracket edge with the
fabric edge

Face this open-
ing outward
towards the room
when mounting

Once the ceiling-mount brackets have been fastened to the ceiling, confirm the

Bracket to Bracket

Width

as listed on the

Sivoia

Order Invoice. Refer to Figure 2 on page 3 for a detailed diagram. Make

any necessary bracket position adjustments based on this assessment.

Summary of Contents for VIMCO SIVOIA SV-MDU-20-KIT

















Search results

Summary of Contents for VIMCO SIVOIA SV-MDU-20-KIT

Reviews:

Related manuals for VIMCO SIVOIA SV-MDU-20-KIT

Brands by name

Popular brands

Lutron Electronics VIMCO SIVOIA SV-MDU-20-KIT, Installation & Operating Instructions Manual

Search results

Summary of Contents for VIMCO SIVOIA SV-MDU-20-KIT

Reviews:

Related manuals for VIMCO SIVOIA SV-MDU-20-KIT

Brands by name

Popular brands