Lund 67572, Original Instructions Manual, Page: 12 / 72

12
GB
O R I G I N A L I N S T R U C T I O N S
67574
The product has been fi tted with touch control panel with light display.
After the product is plugged to mains, an acoustic signal shall be emitted and the display will show: „---”. Also the switch button
shall be backlit. The product is in standby mode.
Touching the button will activate the product setting mode.
The display will alternately show a default temperature and time setting in minutes.
Using buttons marked with a watch symbol you may change time setting.
Using buttons marked with a thermometer symbol you may change temperature setting.
“+” marked button increases and “-” marked button decreases the setting value.
Each touch of a button will be signalled by an acoustic signal and change of setting shown on a display.
“M” marked button allows selecting one of the predefi ned operating modes. Each mode is a combination of time and temperature
settings, shown alternately on a display.
The selection of a mode is signalled by an acoustic signal and backlighting of a symbol of selected mode on a display. In each
mode, time and temperature settings may be changed. However, they will not be saved as new settings of a given mode.
Operating modes can be changed in the following cycle: French fries – ribs – shrimps – cake – poultry – meat – fi sh.
Note! While programming the settings, the product automatically returns to standby mode after about a minute from the last touch
of the button.
After setting the time and temperature, touch the switch in less than one minute. This will start the operation. This will be signalled
by fl ashing of the fan symbol. Backlighting the fan symbol in red indicates the product heater is working. Backlighting the fan
symbol in blue indicates the fan is working.
The product can be switched off at any time by touching the switch button. After switching off , the fan may continue to run for
some time, which accelerates heater’s cooling down process. Then, do not disconnect the product from the power supply. After
the heater has been cooled down, the product will automatically switch into standby mode. Then, unplug the power cord plug
from a mains socket.
Product installation, start-up and handling
The product should be unpacked, by completely removing all packaging components and transport protections. It is recommend-
ed to keep the packaging, it may be helpful for subsequent product transportation and storage.
Wash the product according to instructions contained in the “Product Maintenance” section.
Place the product as per recommendations in this user instruction.
Insert the bowl with the latched and empty insert into the product housing. When inserting the bowl, the cover of bowl’s latch
release button should be moved above the button.
Plug the product to the mains.
Set the maximum temperature.
Set the time to 3 minutes to pre-heat the bowl and insert.
The control light indicating the start of work lights up.
After the set time has elapsed, an acoustic signal is heard and the control light goes out.
Taking safety precautions, grip the bowl handle and pull it out of the product housing. The bowl and insert will be hot, so do not
touch them.
Put the food prepared for thermal processing inside the insert.
If the product is equipped with accessories such as a pot, pizza pan or a compartment, they should be placed in the insert. A bowl
with an installed insert is always required for the proper functioning of the deep fryer.
Note! The level of food products inside the insert must not exceed the check mark of the maximum cubic capacity of the insert.
Slide the bowl with the insert and food into the product housing.
Set the time as per the food preparation prescription.
Periodically check the condition of food being prepared by sliding out the bowl for a moment. If necessary, change the time and/
or temperature settings.
Note! Be careful while sliding out the bowl. The bowl is heated to a high temperature in the course of food preparation. Touch only
the handle. It is recommended to use protective gloves.
After the work is fi nished, unplug the power cord from the mains socket. Leave the product for cooling, and then proceed with
maintenance.
WARNING! During and immediately after the work: the bowl and the insert heat up to high temperature. Special care should be
taken. Contact with heated product components may lead to serious burns.
Tips regarding the use of oil free deep fryer
The use of an oil free deep fryer for preparing food helps to provide an advantage over the process of food preparation in a tra-
ditional oven or deep oil frying.
Lowering the cholesterol content. Thanks to the use of forced air circulation, the fatty tissue of food is reduced thus lowering the
cholesterol content.
Time and energy saving. Thanks to the high effi ciency of forced air circulation method for food preparation, it is possible to reduce