23
Fig. 1
a risk to health. Dust form some tropical woods in particular, and from
hardwoods like beach and oak, is classified as a carcinogenic substance.
Always use a suitable dust extraction device Before machining, remove
any nails and other foreign bodies from the work piece. Specifications
regarding the maximum or minimum size of the work piece must be obser-
ved. Cut thin or thin-walled work-piece only with fine-toothed saw blades.
Never cut several work-pieces at the same time – and also no bundles con-
taining several individual pieces. Risk of personal injury if individual pie-
ces are caught by the saw blade uncontrolled. When cutting round stock,
use a suitable jig to prevent the work-piece from turning. Never cut work-
pieces containing the following materials:
-Ropes, strings, cords, cables and wires.
Do not force the power tool. It will do a better and safer job and give you
much better service if it is used at the rate for which it was designed. Do
not remove chips and work piece parts until the machine is at a complete
standstill. Never operate with the guards not in place – serious risk of in-
jury! Do not stand on the machine. Connection and repair work on the
electrical installation may be carried out by a qualified electrician only.
Always unwind any extension cords fully. Have a damaged or worn cord
replaced immediately. Do not use the machine when the ON-OFF switch
does not operate correctly. The use of accessories other than those recom-
mended in this manual can create a safety hazard. Make all machine ad-
justments or maintenance with the machine unplugged from the power
source. When installing a new sawblade make sure that it matches the ra-
ving knife. The raving knife thickness must be in between sawblade body
thickness and width of cut. Make sure that the sawblade is suitable for the
work piece material to be cut. Use only sawblades according to EN 847-1.
Never use sawblades made from High Speed Steel (HSS). Remove defec-
tive sawblades immediately. A worn table insert must be replaced.
2.3 Remaining hazards
When using the machine according to regulations some remaining hazards
may still exist The moving sawblade in the work area can cause injury.
Broken saw blades can cause injuries. Thrown workpieces can lead to in-
jury. Wood chips and sawdust can be health hazards. Be sure to wear per-
sonal protection gear such as safety goggles ear- and dust protection. Use a
suitable dust exhaust system. The use of incorrect mains supply or a dama-
ged power cord can lead to injuries caused by electricity.
3. MACHINE SPECIFICATIONS
3.1 Technical data BCS 315 B
Machine Table ...............................................mm
550x800
Rear table extensions.....................................mm
550x800
Sawblade diameter ........................................mm
315
Blade bore diameter.......................................mm
30
Blade body thickness.....................................mm
1,8-2,2
Raving knife thickness ..................................mm
2,3
Blade speed 50 Hz.........................................rpm
2990
Cutting height & 90°/45°.......................max mm
90/60
Tilting range of blade ..........................................
90°- 47°
Dust port diameter .........................................mm
100
Working height..............................................mm
800
Weight .............................................................kg
74
20439-6006
Mains ...................................................................
230V~ L/N/PE 50 Hz
Motor input power ...............................................
1600W S1-100%
Reference current..............................................A
7,0
Extension cord (H07RN-F) ..........................mm²
3G1,5
Installation fuse protection ...............................A
16
Protection class ....................................................
I
20439-0207
Mains ...................................................................
400V ~3L/PE 50Hz
Motor input power ...............................................
2000W S1-100%
Reference current..............................................A
3,5
Extension cord (H07RN-F) ..........................mm²
4G1,5
Installation fuse protection ...............................A
16
Protection class ....................................................
I
3.2 Noise emission
Determined according to EN ISO 3744 (Inspection tolerance 4 dB)
Work piece plywood 16mm:
Acoustic power level (according to EN ISO 3746):
Idling
LwA 99,6 dB (A)
Operating
LwA 104,8 dB (A)
Acoustic pressure level (EN 11201): (according to EN ISO 11202)
Idling
LpA 86,7 dB (A)
Operating
LpA 95,5 dB (A)
The specified values are emission levels and are not necessarily to be seen
as safe operating levels This information is intended to allow the user to
make a better estimation of the hazards and risks involved.
3.3 Content of delivery
A Saw guard
B Table insert
C On/Off switch
D Carry handle
E Dust connection hose
F Raving knife
G Rip fence
H Tilting handle
I
Blade rising handle
J
Foldable leg stand
4. TRANSPORT AND START UP
4.1 Transport and installation
Never lift the tool on it’s guards. The sawblade must be covered by the
saw guard during transport. The machine is designed to operate in dry
rooms and must be placed stable on firm and levelled ground. The machi-
ne can be bolted down if required. For packing reasons the machine is not
completely assembled.
WARNING:
To avoid injury, if any parts are missing, do not attempt to
assemble the machine, do not plug in the power cord, do not turn the
switch on until the missing parts are obtained and installed correctly.
4.2 Assembly
Assemble tool in strict accordance with these instructions. Only if you fol-
low the instructions exactly does the machine conform to the safety regu-
lations and can be safely operated. If you notice any transport damage
while unpacking, notify your supplier immediately. Do not operate the
machine! Dispose of the packing in an environmentally friendly manner.
Clean all rust protected surfaces with a mild solvent.
Requirements for machine assembly:
-Philips screwdriver
-22mm wrench
-17mm wrench
-10mm wrench
-8mm wrench
-pair of work gloves
Stand assembly:
The four legs have been folded before shipment.
To assemble the stand:
- unfold the four legs ( J, Fig 2) and tighten the nuts securely.
- insert the short crossbeams and tighten the nuts.
Machine stand
Rear table extension
Rip fence
Sawblade dia 315mm
Raving knife
Saw guard
Dust connection hose and
Y-adapter
2 Wheels
2 Carry handles
Push stick
Operating tools
Operating manual
Spare parts list
3.4 Description of machine