background image

 | + 44(0)208 144 1694  |  [email protected]

Lumishore USA 7137 24TH Court East Sarasota, Florida 34234  |  (941) 405-3302  |  [email protected]

Lumishore UK, Unit D12, Upper Fforest Way, Swansea Enterprise Park, Swansea, SA6 8QR

7

Electrical installation - SUPRA Lumi-Hub

Note: This option requires a Lumishore SUPRA i-Connect Hub (60-0317) and SUPRA i-Connect Switch 
(60-0318). The SUPRA i-Connect Hub is Lumi-Link compatible which allows control via certified MFD or 
connected device (SUPRA Bridge PN: 60-0368) - See SUPRA Bridge installation manual for further details.

Plan the installation first. Work out where the lights will be mounted. Each light connects to the hub using a 
field installable connector (supplied). One hub can power up to 4 lights, and 4 hubs can be connected 
together in one system. The hub should be mounted between the lights and the power source. Plan the 
cable routes, including the switch, prior to installation. Ensure all cables are marine grade, and are correctly 
rated for TOTAL current, and voltage. 

Warranty

Battery / 

PSU 

12 or 24 V

Supra Lumi-

Hub

On/Off

Scene

Supra Lumi-Switch

Field Installable 

Connectors (Supplied)

Removable

Fuse Cover

Fuse or 

Circuit

Breaker

Summary of Contents for eclipse SMX53













Reviews: