background image

4

  

U.L. Model No.: CF654

1. Unpacking Instructions 

 (Continued)

2. Electrical Requirements

To reduce the risk of fire, electric shock, or personal 

injury, mount fan to outlet box marked “Acceptable 

for Fan Support of 22.7 kg. (50 lbs.) or less”, and 

use screws supplied with outlet box. Most outlet 

boxes commonly used for support of light fixtures 

are not acceptable for fan support and may need to be 

replaced. Consult a qualified electrician if in doubt.

 

WARNING

!

Turning off wall switch is not sufficient. To avoid 

possible electrical shock, be sure electricity is turned 

off at the main fuse box or circuit breaker panel before 

wiring. All wiring must be in accordance with National 

and Local codes and the ceiling fan must be properly 

grounded as a precaution against possible electrical 

shock.

 

WARNING

!

To avoid fire or shock, follow all wiring instructions 

carefully.

Any electrical work not described in these 

instructions should be done or approved by a licensed 

electrician.

 

WARNING

!

Your new Ceiling Fan will require a Grounded Electrical 

Supply Line of 120 Volts AC, 60 Hz, 15 Amp Circuit .
The Outlet Box must be securely anchored and capable 

of withstanding a load of at least 50 Pounds .

If your Fan is to replace an Existing Ceiling Light 

Fixture, turn Electricity OFF at the Main Fuse Box 

or Circuit Breaker Panel at this time and remove the 

Existing Light Fixture .

Please call Customer Service at 1-800-777-4440 

if you have any questions about installation and 

operation of this Ceiling Fan .

This Manual Is Designed to Make it as Easy as Possible for You to 

Assemble, Install, Operate and Maintain Your Ceiling Fan

Before assembling your ceiling fan, refer to section 

on proper method of wiring your fan (page 11). 

If you feel you do not have enough wiring knowledge 

or experience, have your fan installed by a licensed 

electrician.

 

WARNING

!

Tools Needed for Assembly

One Phillips Head Screwdriver 

One Stepladder

One Wire Stripper 

One Wire Cutter

Materials

Wiring outlet box and box connectors must be of type 

required by the local code . The minimum wire would be 

a 3-conductor (2-wire with ground) of following size:
  Installed Wire Length 

Wire Size A .W .G .

 

Up to 50 ft . 

14

 

50-100 ft . 

12

Controls 

(Sold Separately)

SR400 Remote Control (sold separately) may be used 

with this 52” SEA BREEZE Ceiling Fan .

THIS FAN IS SUITABLE FOR WET LOCATIONS SUCH AS 

PORCHES, PATIOS AND DECKS.

Summary of Contents for kathy ireland HOME CF654ORB01





















Reviews: