background image

1, Safety instructions and waiver of liability

The

 

following

 

symbols

 

are

 

used

 

throughout

 

this

 

manual

 

to

 

indicate

 

potentially

 

dangerous

 

conditions

 

or

 

mark

 

important

 

safety

 

instructions

Please

 

take

 

care

 

when

 

meeting

 

these

 

symbols

WARNING: Indicates a potentially dangerous condition. Use extreme caution when 
performing this task. 

Dear Client

s

Thank

 

you

 

for

 

purchasing

 

our

 

Max-E

 

Series

 

Solar

 

PV

 

Charge

 

Controller

Your

 

support

 

and

 

trust

 

in

 

us

 

are

 

much appreciated.

 

Please

 

take

 

time

 

to

 

read

 

this

 

manual

this

 

will

 

help

 

you

 

make

 

full

 

use

 

of

 

the

 

many

 

advantages

 

this

 

controller

 

can

 

provide

 

your

 

PV

-

System

 

with

This

 

manual

 

presents

 

important

 

recommendations

 

for

 

installing

operating

 

and

 

monitoring

Read

 

it

 

with

 

special

 

care

 

in

 

your

 

own

 

interest

 

and

 

please

 

pay

 

attention

 

to

 

the

 

safety

 

recommendations

 

herein

 

indicated.

1.2 

The manufacturer shall not be liable for damages, especially on the battery, caused by use other than as 
intended or as mentioned in this manual or if the recommendations of the battery manufacturer are 
neglected. The manufacturer shall not be liable if there has been service or repair carried out by any 
unauthorized person, unusual use, wrong installation, or bad system design.

Liability Exclusion

1.1

 

Safety Instructions

WARNING:

1) 

There are no user serviceable parts inside the 

controller

. Do not disassemble or attempt 

to repair the controller. 

2) Keep

 

children

 

away

 

from

 

batteries

 

and

 

the

 

charge

 

controller

.

CAUTION: Indicates a critical procedure for safe and proper operation of the controller.

1

Summary of Contents for Max-E Series






















Reviews: