Lumel ND30PNET User Manual Download Page 56

Page: 56 / 61

ND30PNET-09 -

User's Manual

ERROR CODES

During the meter operation the display may show error messages. Causes of errors are shown
below.

Err bat

– displayed when the battery of the internal clock RTC is worn. Battery check is

performed after powering. The message can be turned off with the button

Disabled message remains inactive until the meter is turned on again;

Err CAL, Err EE

– displayed when the memory of the meter is damaged. The meter

must be

sent to the manufacturer.

Err PAr

–

displayed when the operating parameters of the meter are incorrect.

Restore the factory settings (from the menu or via RS485). The message can be

turned off with the button

–



–

upper overrun. The value is measured outside the measurement range.

–



–

lower overrun. The value is measured outside the measurement range.

Summary of Contents for ND30PNET






























































Search results

Summary of Contents for ND30PNET

Reviews:

Related manuals for ND30PNET

Brands by name

Popular brands

Lumel ND30PNET, User Manual

Search results

Summary of Contents for ND30PNET

Reviews:

Related manuals for ND30PNET

Brands by name

Popular brands