manualshive.com logo in svg

Lumascape ZDClink, Owner'S Manual

Share
Download
Lumascape ZDClink Owner'S Manual Download Page 26

26

Controller Linking Setup

ZDClink Linking allows for a single point of control for sites 
that require multiple ZDClink Controllers. A linking system can 
contain a total of nine satellite controllers. 

Primary controller

: A ZDClink Controller with a facepack 

installed. Linking firmware is required for both facepack and 
chassis.

Satellite controller

: A controller with no facepack installed. 

Note

Prior to running a Linking system, verify primary and 
satellite controllers have the latest version of linking 
firmware for both the facepack and chassis. 

Note

More information on updating firmware can be found 
under "Firmware Updates" (page 31).

Linking firmware is required for the chassis.

Updating to Linking

1.  From the product page, download the latest facepack and 

chassis ZDClink Linking firmware onto an SD card.

2.  Update facepack firmware.
3.  Update chassis firmware.

Chassis firmware updates take about 15 minutes. The progress 
bar shown at the bottom of the facepack indicates the 
progress of the firmware update. Do not unplug power or Cat 6 
connections while firmware updates are in process.

Summary of Contents for ZDClink











































Reviews:

No comments

Brands by name

Popular brands

Load more brands