the key (included with your pack) or screwdriver. Do
the following in order to adjust it:
3.2.1.10. Switch the clipper on.
3.2.1.11. Turn the adjusting screw clockwise until hear
a loud noise.
3.2.1.12. Then turn the adjusting screw anti-clockwise
until the loud noise stops. This is the optimum point for
the clipper to operate, leave the screw in this position.
Cutting with attachment combs:
3.2.1.13. Depending on the desired hair cut, the clipper
can be operated with or without an attachment comb.
3.2.1.14. There are four attachment combs (3, 6, 9 and
12mm) included with this product.
3.2.1.15. To attach a comb, hold comb with the teeth
showing upward and slide it onto and along the clipper
blade until the front of the comb firmly clicks into the
clipper blade and push the back of the comb down until
it is clipped into position.
3.2.1.16. To remove the comb, simply pull the comb
upward and away from the clipper blade.
How to use the blade lever:
3.2.1.17.
The lever is conveniently located above the
on/off switch so it can easily be adjusted while the
clipper is in your hand.
3.2.1.18. The lever adds versatility to the clipper by
allowing a gradual change to the length of a cut without
an attachment comb.
3.2.1.19. When the lever is in the uppermost position,
the blades will give the closest cut leaving the hair very
short. Pushing the lever gradually downward increases
the cutting length.
3.2.1.20. In its lowest position, the lever will leave the
hair approximately the same length as a #1 comb.
3.2.1.21. The lever will also extend the blade’s life as a
longer cut requires less work from the blades.
3.2.1.22. While the clipper is running, move the Lever
from “close cut” to “longer cut” a number of times.
This will help keep cut hair away from the blades. If the
clipper stops cutting, and the method above does not
help, then the blades are blunt and need to be replaced.
Changing the blades:
3.2.1.23. Switch off the clipper and disconnect from
the mains.
3.2.1.24. Undo both screws on the blades; remove the
bottom blade and top blade.
3.2.1.25. When assembling, the bottom blade and top
blade should be aligned as follows:
3.2.1.26. Raise the adjustable taper control lever to the
shortest cutting length.
3.2.1.27. The distance between the front edge of the
bottom blade and the front edge of the top blade should
be between 0.8mm and 1.5mm.
3.2.1.28. The sides of the two blades should be parallel
to each other.
3.2.1.29. The first tooth of the top blade (from the left)
must cover the first tooth of the bottom blade.
3.2.1.30. The tooth on the far right of the top blade
must touch the outermost large tooth of the bottom
blade.
3.2.1.31. Once aligned tighten both screws.
3.2.2. How to cut the hair:
3.2.2.1. Situate the person whose hair you are going to
cut so that the top of their head is at your eye level.
3.2.2.2. For optimum restults, it is reccomended that
you use the appliance on dry hair, as it is much easier
to control the hair and the result.
3.2.2.3. Hold the appliance in a calm and relaxed man-
ner in order to ensure maximim control of the cut and
a uniform result. Proceed to used short cuts gradually
going around the head.
3.2.2.4. Leave the hair a little longer than the desired
length as it can always be altered later.
3.2.2.5. While working, adapt the comb / comb guid to
achieve the desired result.
3.2.2.6. At regular intervals, stop cutting in order to
comb the hair anf check the results so far.
3.2.3 Nape:
3.2.3.1. Attach comb guide size: 3mm - 6mm.
3.2.3.2. Hold the appliance with the razor facing
downwards and begin to cut the hair from the base of
the neck.
3.2.3.3.Make some upward movements, raising the
appliance gradually and away from the head, cutting
the hair gradually until the height of the ears (Fig. 3)
3.2.4 The back of the head:
3.2.4.1. Attach comb guide size 9-12mm and continue
with the back of the head (Fig 4)
Summary of Contents for Master Barber Kit HCL07AC
Page 8: ......