background image

Manual Rapid Heater DTH

 Feel good through the warmth created from electricity - www.technotherm.de

GB

SELECTION BUTTONS

Selection buttons are used within the menus to display and/or set the several customizable parameters as shown in 

the various sections of this manual.

You can check the set Comfort temperature at any time by pressing a single time the

  

 

or

 

 key. A further pression 

will modify the set temperature. 

Note

: The temperature measured by the inner sensor of the product is representative of the ambient temperature 

nearby it and it may differ from the temperature measured using other instruments in other areas of the room. That 

difference may depend on many factors including, for example:

- the installation position: some areas of the room may be affected by drafts or hot air sacs that modify the sensor 

measurement;

- an external wall fixation: it may imply a temperature measurement  lower than the real room temperature;

- an excessive towels load on the support bar may obstruct the airflow. As a result the sensor may measure a tempe

-

rature higher than the real room temperature;

- unstable conditions: any evaluation must be done in stable working conditions. For this purpose Comfort temperature 

should be changed only 60min after a previous change. In fact, it is not possible to evaluate if the room temperatu-

re is correctly maintained by the product when the Comfort temperature gets repeatedly changed in a short time. 

If the difference between set temperature and room temperature is detected in stable working conditions, measure the 

difference and then increase or decrease the comfort temperature on the product of the exact measured difference 

value.

OK BUTTON

The OK button is used in the various menus to confirm the chosen settings.

BOOST BUTTON

The Boost button allows to activate the timed operation for 15 minutes at maximum power without the thermostat 

control. During this operation the display shows alternately the word "BooS" and the remaining time. At the end of this 

forced operation, the fan heater returns to the previous operating mode.

7. t

roubleshooting

• 

In the event of overheating, the safety device on the appliance automatically disabled the heating elements and 

motor. In this case:

 -

Turn off the fan heater and allow it to cool down for about 15/20 minutes.

 -

Make sure the dust filter is not totally obstructed and clean if necessary. Remember to put it back again 

afterwards.

 -

Eliminate any other possible reasons for overheating (e.g.: obstructions in front of the air inlet/outlet grilles, 

build-ups of dirt).

 -

Turn on the fan heater again and check its correct functioning.

• 

If the touch control commands are blocked or don't answer properly to digital pressure, turn off the heater for at 

least 30sec using the electromechanic switch on the left side of the heater. Then turn on the heater using the 

same switch. 

8. m

aintenance

• 

This product does not require any special maintenance.

• 

Clean the product with a dry cloth at least once every 6 months.

• 

If the product requires repairing, contact an authorised technical service centre.

• 

When replacing the power cable, use a 2x1,00mm

2

 H05VV-F <HAR> type. This operation must be performed 

by qualified personnel and never by the user in order - in order to avoid product damages and safety hazards.

9. l

egal

 

notice

Environment and recycling

To prevent the product from being damaged during transport, it has been carefully packed. To contribute to 

environmental protection, we ask you to dispose of the packaging material properly.

Recycling of obsolete appliances

Appliances with this label must not be disposed off with the general waste. They must be

collected separately and disposed off according to local regulations. Used appliances disposal must be 

carried out carefully and in accordance with local waste disposal regulations.

Summary of Contents for 425 700 100

















Reviews: