Lucent Technologies Network Access Module Installation And Configuration Manual Download | Manualshive

Page: 53 / 75

background image

A-5

Using the DS-1 Test Jacks

Using the DS-1 Test Jacks

The six test jacks provide the means to connect external test equipment to the T1/PRI
line. Table A-3 describes the functions of the individual jacks. Figure A-1 illustrates the
test jack locations. Figure A-2 shows the test jack configuration.

Setting up ACC 2188 PCI Controller

Found 16384K PCI Memory at 0x1ffff000
Testing PCI Memory block 0x20000000-
0x20ffffff ...Passed
Total of 16384K PCI Memory Ready
block alloc 425 870400
block_alloc: cpu<0> control 0028bdb0
free_count<425>

PCI memory has been
correctly set up.

PM3VT/Legend ComOS V4.15.a4.

ComOS version string

.

100R HV=01 FBV=00 FAV=11 FAS=01

MERLIN firmware
identification.

Found x ports

3

Number of ports found,
including C0 and C1.

Ether0 active

PCI-Master

Ethernet interface found.

Running ComOS

N/A

If the system becomes
suspended at this point
and does not print the next
message, the configuration
nonvolatile RAM
(NVRAM) has been
corrupted. Refer to the
PortMaster Troubleshooting
Guide for instructions on
nonvolatile RAM recovery.

PortMaster Console login:

N/A

System is up and running.

Table A-2

Interpreting Diagnostic Boot Messages (Continued)

Field

Possible Message

Explanation

«
...
51
52
53
54
55
...
»

Summary of Contents for Network Access Module












































































Reviews:

No comments

Related manuals for Network Access Module

Brand: D-Link Pages: 32

Brand: D-Link Pages: 6

Brand: D-Link Pages: 221

Express Ethernetwork DI-707P

Brand: D-Link Pages: 14

Brand: Quick Eagle Networks Pages: 4

Brand: National Instruments Pages: 24

Brand: National Instruments Pages: 32

FIELDPOINT FP-1600

Brand: National Instruments Pages: 8

Brand: Paradyne Pages: 20

Compshere 3000 Series

Brand: Paradyne Pages: 2

Brand: Pantech Pages: 17

Brand: Tripp Lite Pages: 2

Brand: DPtech Pages: 39

Brand: KPN Pages: 14

IPAM-1600s Series

Brand: C-Com Pages: 148

Brand: Zalip Pages: 77

EtherFast LNE100TX ver. 5

Brand: Linksys Pages: 42

Brand: UTStarcom Pages: 71

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands