Lucent Technologies Network Access Module Installation And Configuration Manual Download | Manualshive

Page: 48 / 75

background image

Selecting PMVision Functions

6-8

INA Module Installation and Configuration Guide

Figure 6-6

PMVision Backup Dialog

Restore the INA Module Settings

To restore the INA module settings captured in a backup file, select
INA

→

Maintain

→

Restore. Enter or browse to the backup filename on the Restore

panel (Figure 6-7) and click Restore. The restored values overwrite any values existing
in the INA module. A backup file created with a selective backup overwrites only the
selected configuration values and leaves the others unchanged.

Figure 6-7

PMVision Restore Dialog

«
...
46
47
48
49
50
...
»

Summary of Contents for Network Access Module












































































Reviews:

No comments

Related manuals for Network Access Module

Brand: National Instruments Pages: 16

Brand: National Instruments Pages: 23

Brand: process-informatik Pages: 8

LinkSmart KW6515

Brand: Kasda Pages: 31

TeleCLIENT TC7730 Series

Brand: ETL Pages: 83

Brand: Paradyne Pages: 6

CamCon FCS-4000

Brand: LevelOne Pages: 94

Brand: HALNy Pages: 12

Brand: H3C Pages: 4

Brand: Tripp Lite Pages: 2

Brand: Tripp Lite Pages: 2

Brand: NetComm Pages: 124

Brand: Panasonic Pages: 277

Brand: Panasonic Pages: 438

Brand: 8e6 Technologies Pages: 22

Brand: virtual access Pages: 463

FortiExtender 511F

Brand: Fortinet Pages: 18

4 Channel Dimmer Module CLX-1DIM4

Brand: Crestron Pages: 1

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands