manualshive.com logo in svg

Lucent Technologies J85501E-1, Product Manual, Page: 34 / 95

Share
Download
Lucent Technologies J85501E-1 Product Manual Download Page 34

Lucent Technologies Lineage

®

 2000 ECS-6U Controller J85501E-1

Issue 4  August 1998 

Ordering Information  3 - 1

3

Ordering Information

Controller

Table 3-A is a summary of the J85501E-1 List Structure. 
Microprocessor Board and Datalogger Board options (Lists A 
through F and K through N and KA) are discussed in the 
Controller Options Product Manual (167-790-109). Note that all 
options except List BA are shipped separately from the 
controller for connection by installers. Section 2 presents 
detailed descriptions of controller features. 

Table 3-A: ECS-6U Controller Ordering Information

List

Description

1

ECS-6U Controller for -48 volt plants. Provides 

interface to 6 Lucent Technologies Lineage

®

 

2000 rectifiers

2

ECS-6U Controller for +24 volt plants. Provides 
interface to 6 Lucent Technologies 

Lineage

®

2000 rectifiers

3

ECS-6U Controller for -24 volt plants. Provides 

interface to 6 Lucent Technologies Lineage

®

 

2000 rectifiers

6

Kit for one AKC1B shunt isolator circuit pack 
and associated mounting hardware for outboard 
retrofit in a frame with 24-5/16 inch mounting 
centers. Replaces AKC1 (List 5)

7

Same as List 6 except for mounting in a frame 
with 22-5/16 inch mounting centers

A

Optional -48 volt microprocessor circuit pack 
(CP2) to provide local or remote monitoring and 
control functions

B

Same as List A, except with voice response 
feature

Summary of Contents for J85501E-1
































































































Reviews:

No comments