background image

User manual of POE-SW1602/POE-SW2402

 

Safety Instruction

 

These  instructions  are  intended  to  ensure  that  user  can  use  the  product  correctly  to  avoid  danger  or  property 

loss. 

 

The precaution measure is divided into “Warnings” and “Cautions” 

Warnings: 

Serious injury or death may occur if any of the warnings are neglected.

 

Cautions:

 

Injury or equipment damage may occur if any of the cautions are neglected.

 

 

 

 

 

Warnings

 

 

Proper configuration of all passwords and other security settings is the responsibility of the installer and/or 

end-user. 

 

In the use of the product, you must be in strict compliance with the electrical safety regulations of the nation 

and region. Please refer to technical specifications for detailed information. 

 

Input voltage should meet both the SELV (Safety Extra Low Voltage) and the Limited Power Source with 

100~240 VAC or 12 VDC according to the IEC60950-1 standard. Please refer to technical specifications for 

detailed information. 

 

Do not connect several devices to one power adapter as adapter overload may cause over-heating or a fire 

hazard. 

 

Please make sure that the plug is firmly connected to the power socket.     

 

If smoke, odor or noise rise from the device, turn off the power at once and unplug the power cable, and then 

please contact the service center.   

 

 

Warnings

 Follow these safeguards to prevent 

serious injury or death.

 

Cautions 

Follow these precautions to 

prevent potential injury or material 

damage. 

 

Summary of Contents for POE-SW1602






















Reviews: