background image

Privacy Notice 

Surveillance laws vary by jurisdiction. Check all relevant 
laws in your jurisdiction before using all this product for 
surveillance purpose to ensure that your use of this 
product conforms. 

 

Regulatory Information 

FCC Information 

FCC compliance: 

This equipment has been tested and 

found to comply with the limits for a digital device, 
pursuant to part 15 of the FCC Rules. These limits are 
designed to provide reasonable protection against 
harmful interference when the equipment is operated 
in a commercial environment. This equipment 
generates, uses, and can radiate radio frequency energy 
and, if not installed and used in accordance with the 
instruction manual, may cause harmful interference to 
radio communications. Operation of this equipment in a 
residential area is likely to cause harmful interference in 
which case the user will be required to correct the 
interference at his own expense. 

FCC Conditions 

This device complies with part 15 of the FCC Rules. 
Operation is subject to the following two conditions: 

1. This device may not cause harmful interference. 

2. This device must accept any interference received, 
including interference that may cause undesired 
operation 

 
EU Conformity Statement 

This product and - if applicable - the 
supplied accessories too are marked with 
"CE" and comply therefore with the 
applicable harmonized European 

standards listed under the Low Voltage Directive 
2006/95/EC, the EMC Directive 2004/108/EC. 

2002/96/EC (WEEE directive): Products 
marked with this symbol cannot be 
disposed of as unsorted municipal waste in 
the European Union. For proper recycling, 
return this product to your local supplier 

upon the purchase of equivalent new equipment, or 
dispose of it at designated collection points. For more 
information see: www.recyclethis.info. 

2006/66/EC (battery directive): This 
product contains a battery that cannot be 
disposed of as unsorted municipal waste in 
the European Union. See the product 
documentation for specific battery 
information. The battery is marked with 

this symbol, which may include lettering to indicate 
cadmium (Cd), lead (Pb), or mercury (Hg). For proper 
recycling, return the battery to your supplier or to a 
designated collection point. For more information see: 
www.recyclethis.info. 

 

Industry Canada ICES-003 Compliance 

This device meets the CAN ICES-3 (A)/NMB-3(A) 
standards requirements.

 

                    Available from A1 Security Cameras 

    www.a1securitycameras.com email: [email protected]

Summary of Contents for CMHR92T2-28











Reviews: