LTE GlC130D User Manual Download Page 3

Page 3 

 

 

PLEASE READ THESE SAFETY PRECAUTIONS! 

RF Energy Health Hazard  

   

The radio equipment described in this guide uses radio frequency transmitters. Although 
the power level is low, the concentrated energy from a directional antenna may pose a 
health hazard. 

Do not allow people to come in close proximity to the front of the antenna while the transmitter is 
operating. 

Protection from Lightning

 

    

Before connecting this instrument to the power line, make sure that the voltage of the 
power source matches the requirements of the instrument. The unit must be standards. 

Disposal and Recycling Information 

Pursuant to the WEEE EU Directive electronic and electrical waste must not be disposed of 
with unsorted waste.Please contact your local recycling authority for disposal of this product. 

Reduction of Hazardous Substances 

This CPE is compliant with the EU Registration, Evaluation, Authorisation and Restriction 
ofChemicals (REACH) Regulation (Regulation No 1907/2006/EC of the European 
Parliament 

and of the Council) and the EU Restriction of Hazardous Substances (RoHS) Directive(Directive 
2002/95/EC of the European Parliament and of the Council).  

FCC Notice, USA 

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two 
conditions: 
(1) This device may not cause harmful interference, and (2) this device must accept any interference 
received, including interference that may cause undesired operation. 
 
NOTE 1: This equipment has been tested and found to comply with the limits for a Class B digital 
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable 
protection against harmful interference in a residential installation. This equipment generates, uses 
and can radiate radio frequency energy and, if not installed and used in accordance with the 
instructions, may cause harmful interference to radio communications. However, there is no 
guarantee that interference will not occur in a particular installation. If this equipment does cause 
harmful interference to radio or television reception, which can be determined by turning the 
equipment off and on, the user is encouraged to try to correct the interference by one or more of the 
following measures: 
- Reorient or relocate the receiving antenna. 
- Increase the separation between the equipment and receiver. 
-Connect the equipment into an outlet on a circuit different from that to which the receiver is 

connected. 

-Consult the dealer or an experienced radio/TV technician for help. 
 

NOTE 2: Any changes or modifications to this unit not expressly approved by the party responsible for 
compliance could void the user's authority to operate the equipment. 

FCC Radiation Exposure Statement: 

 

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. 
This equipment should be installed and operated with minimum distance 50cm between the radiator & 
your body. 

Summary of Contents for GlC130D
















Reviews: