LTE GlC130D User Manual Download Page 15

Page 15 

 

 

2)  My PC cannot acquire IP from the CPE.  

  First check if the NIC is up and working properly. Then check the PC NIC configuration 

and make sure the DHCP is enabled. 

  Open the MS-DOS window, enter “ipconfig /release” and “ipconfig /renew” commands 

and see if PC can obtain IP correctly.  

  If the problem persists, please contact the operator or distributor for further diagnose. 

3)  My CPE networking is not working properly.  

  You may want to check if the LTE connection is up and running properly. You can do this 

by login the WEB GUI and check the Interface Info page. 

  You may want to perform a factory reset and see if the problem is being corrected. You 

can do this by log into the WEB GUI using “admin” password and perform restore the unit 
to default factory setting.  

 If the problem cannot be corrected by factory reset, please contact the operator or 

distributor for further diagnose. 

4)  I forget the login password and like to reset the unit to factory default.  

  Please contact the operator or distributor and give them the MAC address of the unit. The 

operator or distributor can issue you a RESET password for you to enter in the WEB login 
window.  

  After the unit is reset to factory default, you can login using the default password.  

Summary of Contents for GlC130D
















Reviews: