LSIS LSPV Series User Manual Download Page 44

Page: 44 / 60

*5. Sending Config

Input 0 or 1

0 = no Config data in the waiting queue

1 = Config is sent.

*6. Server IP

Display of the IP address

*7. Server port

Display of the port number of the web server.

*8. Portal test function

Input: “yes”

A data package is sent to the web server (portal).

There is no feedback!

Please contact the Service to learn whether the data package was sent successfully.

4.7 ENS Test

Note:

If the ENS test is carried out while the device is disconnected from
power supply, there will be no result. First restart the device.

Configuration

Extended

XModem Update

Clear data logger

Numerical list

ENS-Test

F1-Menue

ENS-Test

P0900

D0901

P0908

D0902

D0910.

F1-Menue

ENS-Test

D0910.

D0903.

P0909

11500

D0904

230

F1-Menue

P0900.

Start ENS-Test

─

F1-Menue

D0904.

Test result of voltage

test

Volt

F1-Menue

230

ESC

Summary of Contents for LSPV Series





























































Search results

Summary of Contents for LSPV Series

Reviews:

Brands by name

Popular brands

LSIS LSPV Series, User Manual

Search results

Summary of Contents for LSPV Series

Reviews:

Brands by name

Popular brands