background image

LSI Corporation Confidential 

August 2010

Page 7

MegaRAID LSIiBBU08 Intelligent Battery Backup Unit Quick Installation Guide

Connecting the LSIiBBU08 Remotely to the MegaRAID SAS RAID Controller

Figure 3:  Reinstalling the MegaRAID SAS 9280-8e RAID Controller

4. Secure the controller to the computer chassis with the bracket screw.

5. Replace the computer cover and reattach the power cords. 

6. Turn on the power to the computer.

Connecting the LSIiBBU08 
Remotely to the MegaRAID SAS 
RAID Controller

This section describes the two methods you can use to connect the LSIiBBU08 remotely 
to your MegaRAID SAS RAID controller using a cable or, where applicable, a cable and a 
remote interposer board that are sold separately in a Remote Battery Kit:

Use the cable to connect the remote LSIiBBU08 to the BBU connector on the RAID 
controller (

Connecting the LSIiBBU08 Remotely to the MegaRAID SAS RAID Controller

)

Use the cable to connect the remote LSIiBBU08 to a daughtercard that is connected 
to the BBU connector on the RAID controller (

Connecting the Remote LSIiBBU08 to an 

Interposer Card on the MegaRAID SAS RAID Controller

)

The procedures in this section show how to connect the LSIiBBU08 remotely to the 
MegaRAID SAS 9280-8i RAID controller. You can connect the LSIiBBU08 in the same way 
to the other MegaRAID SAS RAID controllers that use this iBBU. 

For information about the BBU connectors on these controllers, see the 

MegaRAID 

6Gb/s SAS RAID Controllers User’s Guide

Connecting the Remote LSIiBBU08 to the 
BBU Connector on the RAID Controller

This section describes how to connect the remote LSIiBBU08 to the BBU connector on 
the SAS 9280-8e RAID controller.

To connect the remote RAID controller to the BBU connector on the RAID controller, 
perform the following tasks in order:

Edge of Motherboard

LSIiBBU08 (Top View)

Bracket Screw

Edge of
Motherboard

85065-02

Press Here

Press Here

Model: B

AT

1S

1P

Model: BA

T 1S1P

WARNING:

The battery used in

this device may present a risk of fire or
chemical burn if mistreated. DO NOT
dissemble, heat above 60C, crush or
puncture, short circuit external contacts,
or dispose in fire or water

.

WA

RNING:

The battery used in

this device may present a risk of fire or
chemical burn if mistreated. DO NOT
dissemble, heat above 60C, crush or
puncture, short circuit external contacts,
or dispose in fire or water

.

Con

tain

s:

Son

y U

S45

426

1A

8T

Cell

Rec

harg

eab

le L

i-P

oly

me

r

Batt

ery

 P

ack

Ratin

g:

3.7

V; 1

.59

Ah; 5

.9W

h

Fin

ishe

d in

 C

hin

a

Contains:
Sony US454261A8T

Cell

Rechargeable Li-Polymer
Battery Pack
Rating:
3.7V; 1.59Ah; 5.9Wh
Finished in China

BBU P/N: L4-25343-04

BBU P/N: L4-25343-04

BBU S/N:SY02700225SO

Li-ion

5

Summary of Contents for MegaRAID LSIiBBU08

















Reviews: