background image

                                                                                                            

R-Log – Quick Start 

 

Cod. INSTUM_00953 

Pag. 12 

 

 

 
Besides, if a measure is used by a derived quantity, the icon changes: 

.  

 
The measures order can be changed according to your requirements by pressing the 

Sort

 button. It is 

however  advisable  to  keep  coupled  the  quantities  that  need  to  be  acquired  together  (for  ex.:  wind 
speed and direction) and give priority to the measures with a fast acquisition rate, moving them on 
top of the list.  
 
 

SETTING THE ELABORATION RATE

 

 
The  elaboration  rate  is  10  minutes  by  default.  If  you  wish  to  change  this  parameter,  select 

Elaborations

 from the 

General Parameters 

section. 

 
 

SETTING THE ACTUATION LOGIC 

 

 
The instrument has 2 actuators that can be used for the power supply of the sensors connected to the 
terminal  board.  Actuators  can  be  also  used  by  programmable  actuation  logics,  able  to  generate 
alarms  in  relation  to  the  values  acquired  by  sensors.  The  voltage  available  on  these  terminals 
depends  on  the  power  supply  provided  by  the  instrument.  The  association  between  input  and 
actuator is fixed and follows the table shown in §3.4. 
 
To set an actuation logic, proceed as follows: 
 
 

 

Select 

Logics

 from the 

Actuators

 section; 

 

Select the first available position (for example (1)) and press 

New

 

Select the type of logic from the 

Value 

column, set the requested parameters and press 

OK

 

Select 

Actuators

 from the 

Actuators

 section; 

 

Select the actuator number for association with the logic (for example (7)) and press the 

New 

key; 

 

Enter a check mark in correspondence to the previously entered logic and press 

OK

 

 

SETTING THE OPERATING CHARACTERISTICS 

 
The most significant operating characteristic is the possibility to turn off your display after about one 
minute  of  non-use  so  as  to  reduce  energy  consumption.  It  is  recommended  to  enable  this  option 
when the instrument operates with a battery, with or without PV panels.  
 
Proceed as follows to access the operating characteristics and - in particular - to set the display auto 
shut-off function:  
 

 

Select 

Characteristics

 from the 

Instrument Information 

section; 

 

Select 

Display auto power off

 and set 

Value

 to 

Yes

 
 

SETTING RADIO COMMUNICATION PARAMETERS  

 

Summary of Contents for ELR510M























Reviews: