LSB ATC32U01A Installation Manual Download Page 13

13

AT C 3 2 U 0 1 A   C o m m u n i c a t i n g ,   P r o g r a m m a b l e   T h e r m o s t a t   -   I O M

C r e a t e d :   1   O c t . ,   2 0 1 2

9.3 DIPSWITCH 

CONFIGURATION

Dipswitch Confi guration mode allows the service personnel 
to view the status of all dipswitch settings for the connected 
communicating control (DXM2/AXM) at the thermostat. 

Navigate between confi guration screens using the left/right 
arrow buttons.  
  

NOTE 1

:  The unit control dipswitch settings cannot be 

changed from the thermostat.

NOTE 2

:  If multiple units are connected to one thermostat, 

refer to section 9.6.

CONTROL CONFIGURATION

DIPSWITCH S1

1     ON   UPS   ENABLED

2     ON   DUAL   COMP   STG   1

3     ON   HEAT   PUMP   TSTAT

4     ON   RV  O   THERMOSTAT

5     ON   DEHUMID   OFF

6     ON   EH2   AUX   HEAT

7     ON   BOILERLESS

8     ON   SEE   DXM2   AOM

 PREVIOUS                                             NEXT 

CONTROL CONFIGURATION

DIPSWITCH S2

1    ON \  ACCESSORY 1

2    ON   ACCESSORY 2

3    ON/

4    ON \ ACCESSORY 2

5    ON ACTIVE W/ COMP

6    ON /

7    ON   H    DEHUM   INPUT

8    ON   FACTORY    SETTING

 PREVIOUS                                             NEXT 

CONTROL CONFIGURATION

DIPSWITCH S3

1    ON    FACTORY    SETTING

2    OFF   HWG   TEST   OFF

3    OFF   HWG   SP   125

4    OFF   HWG   DISABLED

JW3 LT1 SETTING WELL

 PREVIOUS                                        

9.4 FAULT 

HISTORY

Fault History mode displays the fi ve most recent stored fault 
codes for the connected communicating control (DXM2).

Navigate between control fault codes using the up/down 
arrow buttons.  Press the center button to view more 
information about the highlighted fault code.

NOTE

:  If multiple units are connected to one thermostat, refer 

to section 9.7.

9.4.1 Temperature 

Conditions

Displays detailed temperature readings that were 
recorded at the time the fault occurred.

NOTE

: If multiple units are connected to one thermostat, refer 

to section 9.6.

FAULT CONDITION MENU

LT1   LOW   WATER   TEMP

HEAT   1   11:11 AM   11/14

FAULT   TEMP   CONDITIONS

FAULT   FLOW   CONDITIONS

FAULT   I/O   CONDITIONS

FAULT CONFIG COND

FAULT POSSIBLE CAUSES

 PREVIOUS                                        SELECT 

FAULT TEMPERATURE CONDITIONS

LT1   LOW   WATER   TEMP

HEAT   1   11:11 AM   11/14

LT1    TEMP                                                    28.1

LT2    TEMP                                                    97.3

HOT   WATER   EWT                                    121.5

COMP   DISCHARGE                                   157.7

LEAVING AIR                                                  92.7

LEAVING WATER                                           34.9

ENTERING WATER                                        42.1

CONTROL VOLTAGE                                     26.4

 PREVIOUS                                        

YF024    SN - - - - - 0 1 2 3

LAST 5 FAULTS

LT1   LOW   WATER   TEMP

NO   FAULT

NO   FAULT

NO   FAULT

NO   FAULT

                                                                  NEXT 

 PREVIOUS                                        SELECT 

Summary of Contents for ATC32U01A

















Reviews: