LS tractor MT230E 2020 Operator'S Manual Download Page 201

Page: 201 / 218

5 - 53

Caution

▶

The gas generated from the battery can be exploded by spark.

DO NOT connect the negative(-) cable of auxiliary battery to the negative (-)
terminal of tractor battery. Make sure to connect to the engine block.

▶

Keep all flames and sparks away and DO NOT smoke while charging the battery.

④

How to use jumper cables

※

If the battery which is attached to the tractor is discharged and needs to connect a auxiliary battery,

follow the instructions as below.

< Connecting order of jumper cables >

①

②

③

④

Engine

Normal

Discharge

Red cable

Black cable

ⓐ

Connecting Jumper cables



Check followings before connecting the cables.

- Is the spring of clamp normal?
- Is the cable and clamp cut-off?

1. Stop engine, apply parking brake and remove

the ignition key.

2. Connect two (+) terminals of both batteries with

red cable. (tractor battery-

①

, auxiliary battery-

②

)

3. Connect one end of black cable to (-)

terminal(

③

)

of auxiliary battery and the other end to engine
block desired to start (

④

4. Start engine. If the engine does not start, check

the electrolyte level of each battery.

ⓑ

Removing Jumper cables



Remove jumper cables as referring to the right
figure, “Removing order of jumper cables”.

▶

Pay attention not to change the (+) and (-) pole. If not, it may cause a failure of

electric circuit or the damage of wire and even the polarity of battery can be
changed at over-discharged state.

Notice

< Removing order of jumper cables >

①

②

③

④

Engine

Normal

Discharge

Red cable

Black cable

Summary of Contents for MT230E 2020






















































































































































































































Search results

Summary of Contents for MT230E 2020

Reviews:

Brands by name

Popular brands

LS tractor MT230E 2020, Operator'S Manual

Search results

Summary of Contents for MT230E 2020

Reviews:

Brands by name

Popular brands