LS tractor MT230E 2020 Operator'S Manual Download Page 115

Page: 115 / 218

4 - 7

▶

Release clutch pedal slowly. If releasing the clutch pedal suddenly, the gear life can

be reduced and it may cause sudden start.

Notice

Position control lever

Main gear shift lever

Range gear shift lever

Throttle pedal

Brake pedals

Shuttle lever

Clutch pedal

Throttle lever

(2) How to drive

Mechanical type

1. Lift up all the implements (front/middle/rear)

from the ground after starting engine.

3. Press clutch pedal fully and place all the

transmission gear levers (main, range,
shuttle lever) on a suitable position.

4. After pressing down brake pedals, release

the parking brake lever.

5. Release clutch pedal slowly with pressing

down the throttle pedal slowly.

2. Place the throttle lever to the low speed

position.

Summary of Contents for MT230E 2020






















































































































































































































Search results

Summary of Contents for MT230E 2020

Reviews:

Brands by name

Popular brands

LS tractor MT230E 2020, Operator'S Manual

Search results

Summary of Contents for MT230E 2020

Reviews:

Brands by name

Popular brands