manualshive.com logo in svg

LS tractor MT230E 2020, Operator'S Manual

Share
Download
LS tractor MT230E 2020 Operator'S Manual Download Page 111

4 - 3

HST type

Brake pedals

HST reverse pedal

Throttle lever

HST forward pedal

PTO switch

Key switch

1. Sit in driver’s 

seat and apply 
parking brake

2. Place the range gear shift lever 

and HST forward/reverse pedal in 

NEUTRAL

, and PTO switch in 

OFF

.

Parking brake lever

8. Run the engine for a 

few minutes to allow 
engine oil and 
transmission oil to warm 
up.

7. Check if the battery charging 

indicator and engine oil 
pressure indicator are OFF 
after starting engine. 
If not, stop the engine 
immediately and check the 
problem.

3. Pull the throttle lever to 

the low speed position.

6. Turn key switch to 

“

START”

position. As 

soon as the engine 
starts, release the key 
switch to “ON” position.

5. Wait until the cold start 

aid indicator is OFF. 
(about 10 seconds)

4. Turn key switch to “ON”  

position and check if the 
battery charging 
indicator, engine oil 
pressure indicator and 
cold start aid indicator 
are ON.

Caution

▶

Check each part before starting 

engine.

▶

Check if there are any other 

people around before starting.

▶

Place all the transmission gear 

levers and switches in 
NEUTRAL or “OFF” position.

Summary of Contents for MT230E 2020



























































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands