LRX Fresnel Manual Download Page 9 | Manualshive

Page: 9 / 20

background image

LRX™ FRESNEL

Check for the latest manual updates at www.lrx-lighting.com

SPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTICE

9

9

LAMP INSTALLATION



A number of hazards exist during lamp installation please refer to

safety warnings on page two.



This fixture has more than one power supply. Disconnect all power
supplies before installation or removal of the lamps.



Ensure socket is set to appropriate setting for lamp to be used.

See

illustration below.



Prior to installing the lamp, check lamp contacts and wire ends for signs

of arcing or over-heating. If lamp contacts or wiring appear damaged
remove from service.



Ensure power supply matches lamp type, voltage and wattage.



Follow lamp manufactures instructions regarding use and handling of

their product.



Ensure the lamp clamp is tight.



Always clean lamp with alcohol and clean paper towel after installing

lamp.



Allow lamps to cool before removing.

«
...
7
8
9
10
11
...
»

Summary of Contents for Fresnel





















Reviews:

No comments

Related manuals for Fresnel

Brand: Olsen Pages: 56

Brand: Waterous Pages: 5

Brand: 3TECH Pages: 32

Brand: 4EVAC Pages: 15

PORTABLE ICE FISHING KIT

Brand: Garmin Pages: 5

Brand: Gatekeeper Pages: 8

Bure Rise & Go DB 56-309

Brand: Gate Pages: 8

Brand: Hantek Pages: 124

Brand: Hameg Pages: 10

Brand: Fenton Pages: 16

LED Street Bar 16x3W RGB IP65

Brand: Varytec Pages: 9

Brand: VARILITE Pages: 8

EVENTPROFILE VL800

Brand: Vari Lite Pages: 34

Optica 30 Series

Brand: Varex Imaging Pages: 36

Brand: H&S Pages: 54

Brand: Samson Pages: 2

i-Digits Access

Brand: Össur Pages: 231

Brand: LSI Pages: 24

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands