background image

LP Morgan Installation Instructions  | 11

LP Morgan Resi-Lift Manual

Warranty information

Keep your original receipt for warranty.

Please fill out the online warranty form in order to qualify for the manufacturer’s warranty.

http://www.lpmorgan.com.au/owners.html

The  warranty  covers  defects  in  workmanship  and  materials,  provided  this  product 
has been installed in a normal environment and maintained according to the written 
instructions. Herma warrants the product against loss of usefulness, discolouration or 
deterioration of optical quality within the warranty period as a result of manufacturing or 
material defects. This warranty applies only within Australia.

Please return your goods to the place of purchase for all warranty claims.

Conditions  

Any equipment replaced pursuant to the terms of this warranty shall be retained 
by Herma.
All  costs  related  to  de-installation  and  re-installation  of  the  product  covered  by  this 
warranty are not the responsibility of Herma Technologies. Herma will not be responsible 
for any consequential damages during or following installation procedures.
Herma  is  not  responsible  for  any  freight  costs  relating  to  repair  or  replacement.  
Equipment  must  be  returned  to  Herma  in  suitable  packing  to  prevent  damage  in 
transit. Herma will not accept any responsibility for damage to the equipment caused 
by inadequate or unsuitable packing, or for any damage howsoever caused whilst the 
goods are in transit.
Herma  Technologies  shall  not  be  liable  for  any  injury,  loss  or  damage,  direct  or 
consequential, arising out of the use of, misuse of, or inability to use, the equipment.
This  Warranty  does  not  cover  any  product  which  has  been  subjected  to  misuse, 
abuse, neglect, accidental or intentional damage, improper voltage or any alteration 
which affects the reliability or performance of the equipment not attributable to faulty 
manufacture, parts or labour and without limiting the generality of the foregoing.

This  Warranty  does  not  cover  any  product    where  usage,  adaptation  or  installation  
are not in accordance with our written installation and operating instructions. 

Warranty Period:

One year from date of purchase.

Summary of Contents for Resi-Lift















Reviews: