manualshive.com logo in svg

LOYTEC CEA-709, User Manual, Page: 31 / 43

Share
Download
LOYTEC CEA-709 User Manual Download Page 31

L-Switch User Manual 

31 

LOYTEC  

Version 6.0 

 

LOYTEC electronics GmbH   

shapes  or  by  placing  phantom  routers  in  e.g.  NL-220.  Please  contact  LOYTEC  support  if 
you think you need this feature! 

If the mode is changed via the console menu, it cannot changed via the corresponding DIP 
switch  anymore  (see  Section  2.4).  Choose  “[4]  Set router configuration according to DIP 
switch”, to return control to the DIP switch. 

3 - Group learning 

This  menu  option  allows  enabling  or  disabling  learning  of  group  addresses  (see  Section 
4.1.1.3). 

5 – Block unknown domains 

The  L-Switch  XP  will  learn  up  to  four  domains.  If  your  network  contains  more  than  four 
domains please contact LOYTEC support for advice! 

6 – Factory reset w. status button 

In case the L-Switch XP is in the mode repeater or smart switch, pressing the status button 
longer  than  20  seconds  resets  the  switching  tables  (see  Section  5.1).  This  function  can  be 
disabled using this menu option. 

5.3.6  Reset configuration (load factory defaults) 

This menu item allows resetting the device into its factory default state. The following menu 
appears.  

Reset Configuration Menu 
======================== 
 
[1]  Reset everything to factory defaults 
[2]  Reset switch configuration to factory defaults 
[3]  Reset all passwords 
 
[q]  Quit 
 
Please choose: 

Figure 23 Reset to factory defaults menu. 

1 – Reset everything to factory defaults 

Pressing “1” resets the complete device to factory defaults (including error log etc.). 

2 – Reset switch configuration to factory defaults 

Pressing “2” performs a reset identical to pressing the status button longer than 20 seconds 
(see Section 5.5). Use this menu item if you are moving CEA-709 network nodes between 
different CEA-709 channels. 

5.4  Network Diagnostics 

The L-Switch XP provides simple network diagnostics via its port LEDs: 

If the port LED does not light up at all this port is not connected to any network segment or 
the connected network segment currently shows no traffic. 

If the port LED is flashing green the state of the network segment connected to this port is 
ok. 

Summary of Contents for CEA-709












































Reviews:

No comments