background image

O R E N Z

P U L S E  5

28

Connect the searchcoil-connector to the coil-jack and

fasten the plastic sleeve of the connector by rotating

it clockwise. Set mode-switch at position batt. The

needle of the meter should rest near 100 and the red

battery indicator should be off. If the meter displays

a number lower than 50 or if the red light comes on,

the detector should be turned off and immediately

be recharged with the supplied recharger. The battery

condition should be checked via the meter during

operation in the batt.- mode (see chapter 7).

Now turn the mode-switch to the disc position. The

built-in discriminator is now selected. Set the audio

and freq. control to mid-position and retune the

detector with the zero-control. The searchcoil therefore

has to be hold constantly over the ground and the

zero-control must be pushed for about three seconds,

until the preselected audio ticking sound is audible.

Important note:

 With every retuning process one

should pay attention that no metal is in the near of

the searchcoil while pressing the zero-pushbutton.

It is therefore necessary to hold the searchcoil far

away from metal objects and the electronics control

box itself.

During operation no metal buckles or shoes should

be worn. The same with keys, coins, rings and

watches. Every metal carried by the operator can

cause false signals, especially when they are near

the searchcoil. Therefore the electronics control box

has to be carried far away from the searchcoil, this

is especially important while searching with the large

frame mounted coils. Never use any metal screws

when building frames for the universal cablecoils.

The loudspeaker will give one ”tick” every 1-2 seconds

after having retuned the detector correctly with the

zero-control. The ”ticking-rate” can be individually

tuned from silent to a low frequency threshold tone

with the audio-control. This preset audio tone will be

recalled every time the zero-push button is operated.

As the LORENZ PULSE 5 offers it's highest sensitivity

with correctly tuned electronics, one should check

the threshold tone from time to time during operation.

A threshold tone with a ”ticking-rate” will give the

operator the information that the detector works with

it's highest sensitivity.

Especially for target classification purposes the

electronics need to be tuned for best results (see

chapter 5).

The detector is now ready to use and will indicate a

metal object immediately with an audio sound emitted

by the way of loudspeaker or headphones. The audio

frequency will rapidly rise and attains it's highest

frequency when the searchcoil is directly over the

target. The center of the searchcoil is the part with

the highest sensitivity. Even in the direct near of the

target frequency changes make pinpointing possible.

The detector works with it's highest sensitivity in

position Disc and 1. when changing the searchcoil or

when selecting a different position with the mode

control, the electronics need always to be retuned

via the zero-control. When lowering the searchcoil

to the ground especially in position disc and 1 an

audio sound may appear, which can be cancelled by

pressing the zero-pushbutton again. The distance

between the searchcoil and the ground has to be

kept at a constant height when searching after having

done this.

Large diameter coils like the frame mounted cablecoils

should be hold at heights of 4”-24” inches

(10-60 cm) over the ground to ignore magnetic

mineralized ground. Those coils should be moved

slowly without any jerky movements, parallel to the

ground and at constant height.

When mineralized ground conditions or very strong

signals are expected it may be advisible to select a

higher delay setting with the mode control at position

2 or 3.

In position 3 and especially while using large Diameter

frame coils the sensitivity to very small objects

significantly decreases. This is in many cases

desireable. The simplest way to ignore small metal

objekts is to increase the distance between the

searchcoil and the ground. Simply raise the loop and

it will still be possible to locate those deeper bigger

targets. In position disc the target-conductivity can

be measured (see chapter 5).

Note:

 The LORENZ PULSE 5 metaldetector has to be

retuned with the zero control every time the mode

control has been switched to a different position, a

different coil has been connected or the detector has

been turned on again. Therefore the zero-control

has to be pushed for about three seconds. During

operation only very few threshold corrections are

necessary.

In position 2 and 3 the LORENZ PULSE 5 works with

less sensitivity. Position 1 and disc offer the greatest

sensitivity especially for very small non-ferrous metal

objects like coins and nuggets for example. In position

1, 2, 3 no target-classification is possible, but an

intensity meter indication which displays the signal

strength in parallel to the audio sound.

4. Operating procedures I

Summary of Contents for PULSE 5




















Reviews: