Your child seat can be installed
ONLY
with the help of 3-point belts!
!!
ONLY
in the
OPPOSITE
direction of
movement of the car!
Step
2.
Place the child seat on the seat of the car
in the
OPPOSITE
direction of movement of the car
,
ensuring it is firmly pressed against the car seat backrest.
on the passenger seat,
If your car has an air bag
the child seat should be used only in the rear of the car!
Step
8
.
Place the child in the seat. Check the height of the shoulder belts. Make sure the straps are not
twisted or hanging somewhere. Fasten the seat belts on the child, making sure that they are well placed and
pull the strap in the centre of the seat to tighten.
Please use 3-point safety belts of the car to ensure the safety of the child and to secure the child seat!
3.
Insert both ends of canopy frame into the canopy frame joint “16" parts which locate on the both side of the
car seat and above the handle. (Picture 14 )
WARNING!
The child MUST not to be in the child seat when installing the seat into the car and adjusting the
car belt The vehicle has to be on even surface!
Step 1.
Adjust the handle to the upright position .
Стъпка 3.
Slide the lap belt of the vehicle’s 3-point seatbelt through both Lap belt guides .Let the tongue plate
snap in the belt lock with a clearly audible ”click”. (Picture 10) Pull the shoulder belt in arrow direction to
tighten the lap belt. Check to make sure the tongue plate is locked by pulling on the belt .
Step
4.
Place the diagonal belt in the diagonal belt guide at the back of the seat
(
Picture 11
)
Step 5.
Tighten the vehicle’s own 3-pointseatbelt by pulling hard on the positions .
(
Picture 11
)
Step 6. Adjust the handle to the forward position
! Place the child safety seat on the vehicle's seat ensuring
its handle must be firmly against the car seat backrest.
(
Picture 10;11
)
Step
7.
Make sure that the belt is not twisted and strongly tightened. Make sure the seat is fixed firmly on the
car seat.
Assembling of the canopy.
1.
Adjust the handle to the down position behind the back. (Picture 12)
2.
Insert frame “17" through sleeve of canopy. (Picture 13)
5.
Rotate the canopy frame joint parts and the canopy will reach the proper position you want (Picture 16),
after that rotate the carry handle in the desired position (
Picture 17
)
Removing the canopy Picture 18
Removing the upholstery Picture 19
4.
Fix the bottom of the canopy cover to the top of the car seat back. (
Picture 15
)
INSTALLATION OF SEAT
"Group 0+"
/ newborn and weighing up to 13 kg. /
14
Ensure that the handle is locked in a position ,the harness is correctly fitted and buckle fastened
before carrying your car seat.
1 Position
- Forward facing installed in the car .This position (only this position)
2.
Make sure the belt is locked by pulling the shoulder straps up. (Picture 8)
3.
To release belt, press down the red button on the central buckle “3”.
3 Position
- Handle clicked back to initiate the rocking feature .
The carry handle of the car seat , can be adjusted in 4 stable positions.
Adjusting of the carry handle
Adjusting the length of the belts
is suitable for the baby car seat installed on the vehicle seat .
2 Position
- Straight up for carrying.
4 Position
- Down to support baby for feeding.
To adjust the handle ,please press the red button on handle on both side at the same time. Now it can be
rotated. (
Picture
9)
1.
Slack the belts: Press the button for belts adjusting "5" and at the same time pull both shoulder straps.
(Picture 3)
2.
Tightening the belt: Place your child in the seat, fasten both belts in the buckle in the center and pull the
strap “4" in the middle of the seat. (Picture 5)
