manualshive.com logo in svg

LORD 6254-4220, User Manual

Share
Download
LORD 6254-4220 User Manual Download Page 38

3DM

®

-GX5-15

User Manual

7.1.1

Packet Builder

To expedite program development, a packet builder tool is included in the MIP Monitor software.

The packet builder allows users to send multiple packets to the 3DM-GX5-15 and view the resulting

reply data.

Applicable protocol structure and design is described in the 3DM-GX5-15 LORD Sensing MIP Data

Communications Protocol (DCP) Manual DCP Manual . For additional help, contact Technical

Support (

see Technical Support on page 47

).

To use the packet builder select Advanced > Packet Builder from the MIP Monitor main window (

7.1.1

Packet Builder

). The sensor must be in the Standard communications mode to use this

feature.

Figure 26 -Packet Builder

7.1.2

Sensor Direct Mode

The MIP Monitor software can be used to put the sensor in a mode that allows direct programmatic

access to the internal Inertial Measurement Unit (IMU). The IMU has its own processor and protocol

commands and native data outputs from the individual IMU sensors that may not be available in

MIP Monitor.

When in Sensor Direct mode the device normal functionality is not available. The protocol

commands used to interface with the IMU are a subset of the standard LORD Sensing MIP Data

Communications Protocol (DCP) and are further described in the LORD Sensing MIP Data

Communications Protocol (DCP) manual. For additional information contact LORD Sensing

Technical Support (

see Technical Support on page 47

).

38

Summary of Contents for 6254-4220


































































Reviews:

No comments

Brands by name

Popular brands

Load more brands