manualshive.com logo in svg

LORD 6254-4220, User Manual

Share
Download
LORD 6254-4220 User Manual Download Page 20

3DM

®

-GX5-15

User Manual

4.

Sensor Measurements

The 3DM - GX5 - 15 block diagram (

Figure 14 - 3DM- GX5- 15 Block Diagram

) describes its primary

hardware components and internal configuration. Integrated Micro-Electro-Mechanical System (MEMS)

sensors within the 3DM- GX5- 15 are collectively known as the Inertial Measurement Unit (IMU) and

include tri-axial gyroscopes (gyros), tri-axial accelerometersand a pressure altimeter. This technology

provides direct measurements of acceleration, angular rate, pressure, Delta-theta (change in angular

rate), and Delta-velocity (change in velocity). Temperature and pressure sensors provide environmental

information for measurement compensation and altitude estimations. information can be read directly but

is not used internally for attitude or navigation estimations on the 3DM-GX5-15.

Computed estimations for attitude, acceleration, angular rate, and heading are available outputs on the

3DM-GX5-15. To achieve these estimations, the MEMS sensors are processed by an IMU Estimation

Filter (EF) microprocessor with an Adaptive Kalman Filter (AKF) . Additional user settings such as

measurement filtering, biasing, and tolerance values offer adjustments for specific applications.

Figure 14 -3DM-GX5-15 Block Diagram

20

Summary of Contents for 6254-4220


































































Reviews:

No comments

Brands by name

Popular brands

Load more brands