Loopcomm LP-8696C User Manual Download Page 10 | Manualshive

Page: 10 / 75

background image

WLAN Broadband Router

User Manual

- 10 -

3.

Installation

3.1

Hardware Installation

Step 1:
Place the WLAN Broadband Router to the best optimum transmission location. The best transmission
location for your WLAN Broadband Router is usually at the geographic center of your wireless
network, with line of sign to all of your mobile stations.

Step 2:
Connect the WLAN Broadband Router to your wired network. Connect the Ethernet WAN interface of
WLAN Broadband Router by category 5 Ethernet cable to your switch/ hub/ xDSL modem or cable
modem. A straight-through Ethernet cable with appropriate cable length is needed.

Step 3:
Plug in the DC power to the WLAN Broadband Router. Use only the AC/DC power adapter supplied
with the WLAN Broadband Router; it maybe occur damage by using a different type of power adapter.

The hardware installation finished.

3.2

Software Installation

There are no software drivers or utilities installation needed, but only the
configuration setting. Please refer to chapter 4 for software configuration.

Notice:

It will take about 50 seconds to complete the boot up sequence after powered on the WLAN

Broadband Router; Power LED will be active, and after that the WLAN Activity LED will be flashing
to show the WLAN interface is enabled and working now.

«
...
8
9
10
11
12
...
»

Summary of Contents for LP-8696C












































































Reviews:

No comments

Related manuals for LP-8696C

Brand: Enterasys Pages: 36

Spectrum24 AP-41X1-1050 HR

Brand: Symbol Pages: 2

Brand: InfiNet Wireless Pages: 100

Jetpack MiFi 4510L

Brand: Verizon Pages: 88

UniFi AP AC Outdoor

Brand: Ubiquiti Pages: 26

Brand: CNET Pages: 2

Brand: FS Pages: 36

Brand: Cambium Networks Pages: 61

Brand: Caimore Pages: 83

Brand: SoundPeats Pages: 50

Brand: Rugged Radios Pages: 2

Brand: Ruckus Wireless Pages: 4

Brand: Ruckus Wireless Pages: 12

Brand: RTS Pages: 2

Brand: Comet Labs Pages: 46

Brand: Air Live Pages: 72

Wireless-N Broadband Router

Brand: Comtrend Corporation Pages: 165

Brand: ConnectGear Pages: 11

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands