manualshive.com logo in svg

Loopcomm LP-8696C, User Manual

Share
Download
Loopcomm LP-8696C User Manual Download Page 9

WLAN Broadband Router 

User Manual 

- 9 - 

2.3

 

Rear Panel Description 

 

 

Interfaces   

Description   

Antenna (Fixed / SMA)   

The Wireless LAN Antenna.   

Power   

The power jack allows an external DC power supply connection.   

The external DC adaptor provide adaptive power requirement to the 
WLAN Broadband Router.   

WAN   

The RJ-45 socket allows WAN connection through a Category 5 cable. 
Support auto-sensing on 10/100M speed and half/ full duplex; comply 
with IEEE 802.3/ 802.3u respectively.   

LAN   

The RJ-45 sockets allow LAN connection through Category 5 cables. 
Support auto-sensing on 10/100M speed and half/ full duplex; comply 
with IEEE 802.3/ 802.3u respectively.   

WPS   

Push the WPS button implementation to reduce the network 
configuration steps, and also easy to implement network security.   

Reset   

Push continually the reset button 5 ~ 10 seconds to reset the 
configuration parameters to factory defaults.   

Summary of Contents for LP-8696C












































































Reviews:

No comments

Brands by name

Popular brands

Load more brands