Loopcomm LP-7665 Page 3 User Manual Download

Page: 3 / 55

Introduction

1.1

Welcome

PCI Adapter connects you with IEEE802.11n networks at receiving rate up to an incredible 300Mbps!

By using the reflection signal, 802.11n technology increases the range and reduces "dead spots

in the

wireless coverage area.

Unlike ordinary wireless networking of 802.11b/g standards that are confused by wireless reflections,

802.11n can actually use these reflections to increase four times transmission range of 802.11g
products.

Besides, when both ends of the wireless link are 802.11n products, The PCI can utilize twice radio
band to increase three times transmission speed of ordinary 802.11g standard products, and can comply
with backwards 802.11b/802.11g standards.

Soft AP supported by PCI Adapter can help you establish wireless LAN networking with lowest cost.

Besides, WPS (PBC and PIN) encryption method can free you from remembering the long passwords.

Complete WMM function makes your voice and video more smooth.

1.2

Product Feature

Complies with IEEE 802.11n , IEEE 802.11g, IEEE 802.11b standards

Provides 32-bit PCI interface

Provides 300Mbps receiving rate and 300Mbps sending rate

Supports 20MHz/40MHz frequency width

Auto-detects and changes the network transmission rate

Provides two work modes: Infrastructure and Ad-Hoc

Supports Soft AP to establish your wireless LAN networking with lowest cost

Supports 64/128-bit WEP, WPA, WPA2 encryption methods and 802.1x security authentication

standard

Supports WPS (PBC and PIN) encryption method to free you from remembering long passwords

Supports WMM to make your voice and video more smooth

Supports Windows

2000, XP 32/64, Vista 32/64, win 7 32/64

1.3

Contents of Package

One PCI Card

One Installation CD w/User Manual

Two Detachable 2 dBi antennas

Contact your local authorized reseller or the store purchased from for any items damaged and/or
missing.

Summary of Contents for LP-7665
























































Search results

Summary of Contents for LP-7665

Reviews:

Related manuals for LP-7665

Brands by name

Popular brands

Loopcomm LP-7665, User Manual

Search results

Summary of Contents for LP-7665

Reviews:

Related manuals for LP-7665

Brands by name

Popular brands