manualshive.com logo in svg

Loopcomm LP-7665, User Manual, Page: 40 / 55

Share
Download
Loopcomm LP-7665 User Manual Download Page 40

Describe "WPS Status Bar" -"PBC - xxx" as follow : 

A successful PBC Configuration : 

Start PBC connection ~> Scanning AP ~> Begin associating to WPS AP ~> Associated to WPS AP ~> 
Sending EAPOL-Start ~> Sending EAP-Rsp (ID) ~> Receive EAP-Rsp (Start) ~> Sending M1 ~> 
Received M2 ~> Sending M3 ~> Received M4 ~> Sending M5 ~> Received M6 ~> Sending M7 ~> 
Received M8 ~> Sending EAP-Rsp (Done) ~> Configured ~> WPS status is disconnected ~> WPS 
status is connected successfully-SSID 

No PBC AP available : 

Scanning AP ~> No PBC AP available ~> Scanning AP ~> No PBC AP available   

~>...

Too Many PBC AP available : 

Scanning AP ~> Too Many PBC AP available ~> Scanning AP ~> Too Many PBC AP available ~>... 

WPS configuration doesn't complete after 

two-minute connection

: WPS Eap process failed. 

When Errors occur within 

two-minutes of establishing a connection

, the WPS status bar might 

report "WPS Eap process failed" 

Error messages might be: 

1. Receive EAP with wrong NONCE. 

2. Receive EAP without integrity. 

3. An inappropriate EAP-FAIL received. 

Describe "Multiple PBC session overlaps" as follow: 

Dual bands:   

AP1 is a G-Band AP using PBC mode. (ID = 0x0004)   

AP2 is a A-Band AP using PBC mode. (ID = 0x0004)   

They have the same UUID-E.   

STA would regard these two APs as a dual-radio AP and select one band to connect. 

Different UUID-E: 

AP1 is a G-Band AP using PBC mode. (ID = 0x0004)   

40

Summary of Contents for LP-7665
























































Reviews:

No comments