background image

DMUI-EASY2MOVE - OPERATING MANUAL // PAGE 8

2.7  RESIDUAL RISKS

Residual risks are the risks that remain after all relevant safety standards have been complied with. These 
have been evaluated in the form of a risk assessment. Residual risks associated with the installation of the 
DMUI-EASY2move Handset are listed here and throughout this Operating Manual. See also Chapter 1.1 
Other Applicable Documents on page 5. The symbols and signal words used in this Operating Manual are 
listed in Chapter 2.5 Explanation of Symbols and Signal Words on page 7. 

WARNING Risk of death or serious injury through electric shocks

DMUI-EASY2move Handsets are electrical devices. Although you will not have to con-

nect the Handset to the Power Hub during assembly, basic safety precautions must be 

taken at all times. Failure to observe electrical safety precautions may lead to death or 
serious injury through electric shocks. 

•  Never open the Handset

•  Ensure that the Handset is not connected to the Power Hub during assembly

•  Do not convert or modify the Handset in any way

•  Do not immerse the Handset or its components in liquid. Clean only with a dry or 

slightly damp cloth

•  Do not place the Cable of the Handset on heated surfaces

•  Check the housing and cables of the Handset for visible damage. Do not install or 

operate damaged products. 

WARNING Risk of death or serious injury in explosive atmospheres

Operating the Handset in potentially explosive atmospheres may lead to death or seri-

ous injury through explosions.

•  Read the relevant directives to determine if an atmosphere is potentially explosive

•  Do not operate the Handset in potentially explosive atmospheres

WARNING Moderate risk of serious injury through electric shocks

While cleaning or using the system, liquid intrusion may lead to serious injury through 
electric shocks. 

•  Do not allow any components to become wet during cleaning

•  Ensure components are placed away from areas where spillages are likely to occur

•  Take care not to spill liquids onto or around the system

•  If liquid intrusion does occur, replace the Handset immediately.

CAUTION

Risk of minor or moderate injury through tripping

During the assembly process, you may have to step over Cables. Tripping over Cables

may lead to minor or moderate injury.

•  Ensure that the assembly area is kept clear of unnecessary obstructions

•  Be careful not to trip over Cables

CAUTION

Risk of minor or moderate injury through crushing

If  excessive force is applied to the DMUI-EASY2move, the Table System may become 

damaged. The use of damaged products may lead to minor or moderate injury through 

crushing.

•  Do not apply excessive force to the Handset

Summary of Contents for DMUI-EASY2move




















Reviews: