background image

69

            

Installation & Operation Manual

11  

Operating information 

(continued)

Access modes

User

The user can adjust space heating and tank target temperatures 
by pressing the NAVIGATION dial when “

SETPOINTS” is 

flashing at the bottom of the display.  The date and time, and 
the temperature units can also be changed (see page 63).

Installer

Most parameters are available only to the installer, accessible 
by entering the installer password, see the Knight Wall Mount 
Service Manual.

Saving parameters 

(reference the Parameter Table in 

the Knight Wall Mount Service Manual)

To save parameters and exit programming:

Press the RIGHT SELECT [SAVE] key and then press the 
RIGHT SELECT [HOME] key.

To enter a parameter and continue programming:

Press the RIGHT SELECT [SAVE] key 1 time to return to the 
parameter listings; press again to return to the menu listings.  
Remember to press the RIGHT SELECT [HOME] key when 
finished programming in order to save the changes made.

See the Knight Wall Mount Service Manual for a detailed 
description of parameters and access modes.

OPERATION

DISPLAY

8.  If the space heating call for heat is active, and the tank thermostat 

or sensor starts a DHW call for heat, the boiler will switch to the 
DHW mode.  If programmed for normal DHW operation (not as a 
zone), the DHW pump will turn on first, then the boiler pump will 
turn off (boiler and DHW pump operation briefly overlap to ensure 
flow is maintained through the unit). This will divert the boiler’s 
outlet water from the heating system and send it to the tank coil 
instead. The control will then modulate to maintain the outlet 
temperature to the DHW boiler set point.

9.   If the boiler is not part of a Cascade, and both the space heating  

and DHW calls for heat remain active long enough, the boiler will 
switch back and forth between the two heating modes until one of 
them is satisfied.

10.  Once both calls for heat are satisfied, the control will turn off 

  the burner.  The blower will continue to run during the postpurge 
  period.

11.  Any pumps that are running will continue to run for their respective 

pump delay times before turning off, unless programmed to 
remain on continuously.  A 60 second anti-cycle period will start, 
which will delay any new call for heat until it times out.

12.  In Standby, ready to start a new cycle.

Please note that the brackets ([]) denote 
screen status.

 NOTICE

Summary of Contents for Knight WHN055

















































































Reviews: