background image

9

3  

Operating instructions

                  

User’s Information Manual 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

FOR YOUR SAFETY READ BEFORE OPERATING

WARNING:

  If you do not follow these instructions exactly, a fire or explosion

may result causing property damage, personal injury, or loss of life.

A.  This appliance does not have a pilot.  It is
     equipped with an ignition device which
     automatically lights the burner.  Do not try
     to light the burner by hand.

B.  BEFORE OPERATING smell all around
     the appliance area for gas.  Be sure to
     smell next to the floor because some gas
     is heavier than air and will settle on the
     floor.

WHAT TO DO IF YOU SMELL GAS

‡'RQRWWU\WROLJKWDQ\DSSOLDQFH

‡'RQRWWRXFKDQ\HOHFWULFVZLWFKGR

   not use any phone in your building.

‡,PPHGLDWHO\FDOO\RXUJDVVXSSOLHUIURPD

   neighbor’s phone.  Follow the gas supplier’s
   instructions.

C.  Use only your hand to turn the gas control knob.
     Never use tools.  If the handle will not turn by
     hand, don’t try to repair it, call a qualified service
     technician.  Force or attempted repair may result
     in a fire or explosion.

D.  Do not use this appliance if any part has been
     under water.  Immediately call a qualified
     service technician to inspect the appliance and
     to replace any part of the control system and
     any gas control which has been under water.

‡,I\RXFDQQRWUHDFK\RXUJDVVXSSOLHUFDOO

   the fire department.

1.  

STOP!

  Read the safety information

     above on this label.

2.  Set the thermostat to lowest setting.

3.  Turn off all electric power to the
     appliance.

4.  This appliance is equipped with an
     ignition device which automatically lights
     the burner.  Do not try to light the burner
     by hand.

5.  Remove top cover.

6.  Turn gas shutoff valve counterclockwise
     to “OFF”.  Handle will be perpendicular to
     pipe.  Do not force.

7.  Wait five (5) minutes to clear out any gas.
     If you then smell gas, 

STOP!

  Follow “B”

     in the safety information above on this label.
     If you don’t smell gas, go to next step.

8.  Turn gas shutoff valve clockwise to “ON”.
     Handle will be parallel to pipe.

9.  Install top cover.

10.  Turn on all electric power to appliance.

11.  Set thermostat to desired setting.

12.  If the appliance will not operate, follow the
       instructions “To Turn Off Gas To Appliance” and
       call your service technician or gas supplier.

1.  Set the thermostat to lowest setting.

2.  Turn off all electric power to the appliance
     if service is to be performed.

3.  Remove top cover.

4.  Turn gas shut off valve counterclockwise to
     “OFF”.  Handle will be perpendicular to pipe.
     Do not force.

5.  Install top cover.

LBL2284 REV -

TO TURN OFF GAS TO APPLIANCE

OPERATING INSTRUCTIONS

Summary of Contents for KNIGHT 400 - 801

















Reviews: