background image

 

                                          CHAPTER 3:    Troubleshooting                                                       

 

3.3 TROUBLESHOOTING – NO CONSOLE RESPONSE     

 

TH

E

 POW

ER

 

I

S ON, BUT MACHINE H

AS 

NO 

RE

SPONS

1)    SYMPTOM:

 

a. The power is on and the console lights up, but the treadmill does not run when keys are pressed.     

 

2)    SOLUTION: 

         

a. Check if the console beeps when all keys are pressed. If no, replace the keypads.       

b. Enter Engineering Mode (See Section 4.1), and scroll to ENG 1 (Hardware Test).Press the key “ENTER” first and 

then the key ”START”. 

 

                - When press the key “SPEED + / -“, if the data on windows “TIME” & “DISTANCE” is changed, the console is ok. 

If not, replace the PCB. 

c. Turn off the power switch, and open the motor upper cover. Remove the red & black wires of motor from the MCB, 

and u

se a multi-meter to measure the resistance of drive motor.

 

If the resistance is bigger than 10 

ȍ

, the drive motor is defective. 

Replace the drive motor. 

 

 

If the resistance is lower than 10 

ȍ

, the drive motor is ok. Then, 

- Check the connection of the speed sensor (encoder disk group) at the MCB (Figure A). 

- Remove the speed sensor (Figure B) from the motor and clean it, then re-test. 

- If the speed sensor is clean and has a good connection but still will not operate, replace the speed sensor. 

- Replace the MCB as the last step if machine does still not run after to take above actions.

 

 

 

 

 

 

 

 

 

 

 

 

FIGURE A 

FIGURE B 

Summary of Contents for LSPRO2
















Reviews: