background image

10  GB/IE/NI

Initial use / Installing the LED strip

Safety / Initial  use

  

Never throw batteries / rechargeable batteries 
into fire or water.

  

Do not exert mechanical loads to batteries /  
rechargeable batteries.

Risk of leakage of batteries /  
rechargeable batteries

  

Avoid extreme environmental conditions and 
temperatures, which could affect batteries /  
rechargeable batteries, e.g. radiators / direct 
sunlight.

  

If batteries / rechargeable batteries have leaked, 
avoid contact with skin, eyes and mucous mem-
branes with the chemicals! Flush immediately 
the affected areas with fresh water and seek 
medical attention!

  

WEAR PROTECTIVE GLOVES! 
 
 

Leaked or damaged batteries / rechargeable 
batteries can cause burns on contact with the 
skin. Wear suitable protective gloves at all times 
if such an event occurs.

  

In the event of a leakage of batteries /  
rechargeable batteries, immediately remove 
them from the product to prevent damage.

  

Only use the same type of batteries / recharge-
able batteries. Do not mix used and new  
batteries / rechargeable  batteries.

  

Remove batteries / rechargeable batteries if the 
product will not be used for a longer period.

Risk of damage of the product

  

Only use the specified type of battery /  
rechargeable battery!

  

Insert batteries / rechargeable batteries according 
to polarity marks (+) and (-) on the battery /  
rechargeable battery and the product.

   Use a dry lint-free cloth or cotton swab to clean 

the contacts on the battery / rechargeable battery 
and in the battery compartment before inserting!

  

Remove  exhausted  batteries / rechargeable 
batteries from the product immediately.

  Initial use

   Remove all packaging materials before first use.
   Never connect the LED strip to the mains power 

supply while it is in the packaging and rolled up.

 

 Note:

 Ensure that a plug socket is located in 

close proximity to the installation area.

  

Replacing / Inserting  batteries 

(14125106LE)

 

 Note:

 Before first use, pull the insulating strip 

14

 out of the battery compartment 

13

.

   If the range of the remote control 

4

 reduces, 

the battery 

15

 needs to be replaced. To do this, 

take the battery compartment out of the remote 
control 

4

. Remove the old battery 

15

 and in-

sert a new one.

 

 Note:

 The correct polarity is indicated on the 

reverse side of the remote control 

4

.

   Slide the battery compartment 

13

 back into 

the remote control 

4

.

  

 Trimming / connecting   

the LED tape

The LED tape may be trimmed to size or connected.

 

DANGER TO LIFE BY ELEC-

TRIC SHOCK! 

Disconnect the lights from the power supply before 
performing any work on the LED strip 

3

. Unplug 

the mains adapter 

2

 from the socket to do so.

   Choose the desired LED strip length.

 

 Note 

Ensure that you cut the LED strip at the 

right place. The cutting point lies exactly between 
the plus and minus pole and is marked with a 
black line (14125106LE: + 12 V, blue, red, 
green -  ; 14125206LE: +, -) (see Fig. C).

   Shorten the LED strip 

3

 using a pair of scissors.

   Then press both ends of the LED strip 

3

 onto 

the displacement contact of the connector 

8

 

(see Fig. C).

 

 Ensure the correct polarity of the connector 
when connecting the LED strip 

3

 (14125106LE: 

Summary of Contents for 14125106LE


























Reviews: