page 3
INSTALLATION INSTRUCTIONS
YOKE MOUNT
•
To intstall Yoke, thread cord through offset center hole of upper yoke
section.
• Secure Yoke to housing with four 1/2” 1/4-20 Socket Cap Screws. Use
3/16” Allen wrench to tighten to min. 2.2ft-lbs (3Nm) to max. 2.6ft-lbs
(3.5Nm).
•
Mount fixture to the desired bracketry with one 5/8” or two 1/2” bolts,
lock washer, and nut (not provided). See figure B for template of yoke
bracket hole pattern.
•
To adjust the tilt angle of the fixture, use 5/16” Allen wrench to loosen
the 3/8-16” Socket Cap screws on both sides of the yoke. While holding
weight of fixture, use 5/32” Allen wrench to remove #10-24 Socket Cap
set screw, adjust to desired angle and reinstall set screw in appropriate
matching hole. Re-tighten hex head screws to min. 2.5ft-lbs (3.5Nm) to
max. 3ft-lbs (4Nm). See Figure C.
FIXTURE PACKING LIST
Description
Quantity
A LED Light Fixture
...............................................................................1
B Slipfitter
B Slipfitter
.............................................................................................1
C
C Yoke
Yoke .................................................................................................1
*Contained in parts packs
Remove fixture components and parts pack.
Check to ensure all parts
are included.
Note:
Account for small parts and destroy packing material,
as these may be hazardous to children.
Features
ESXF3 ALO
ESXF4 ALO
switchable photocontrol
ON*/OFF
color temperature
3000/4000*/5000K
adjustable lumens
High 14,000*
Med 10,500
Low 8,500
High 20,000*
Med 18,000
Low 16,000
Slipfitter
included
Yoke
included
CHOOSE SETTINGS
(OPTIONAL)
Figure A
*Factory setting
FIXTURE INSTALLATION
For installation to properly installed and grounded UL listed recessed or
surface mounted weatherproof junction box.
CAUTION: WIRING
Make sure power is turned off.
•
Use wire nut to connect the bare copper or green house supply
ground wire to the green fixture ground wire.
Note:
If house wiring
does not include a ground wire, consult your local electrical code for
approved grounding methods.
For proper connection, place wire nut over wires
and twist clockwise until tight.
•
Use wire nut to connect the white fixture wire to the white (neutral)
house supply wire.
•
Use wire nut to connect the back fixture wire to the black house
supply wire.
Turn on electricity at fuse or circuit breaker box and verify success of
installation.
Note: If photosensor is in ON postion, cover photosensor
window to block daylight from entering sensor and allow lights to activate
during daytime.
Turn OFF Power at circuit breaker box.
CAUTION:
Do not rely on wall switch alone to turn off power.
SLIPFITTER MOUNT
•
To Install slipfitter, thread cord through slipfitter (B).
•
Secure Slipfitter to housing with four 1/2” 1/4-20 Socket Head Cap
Screws. Use 3/16” Allen wrench to tighten to min. 2.2ft-lbs(3Nm) to
max. 2.6ft-lbs (3.5Nm).
• Make power connection, see wiring instructions.
•
Place integral slipfitter onto maximum
2-3/8” outer diameter Tenon.
Secure slipfitter to the Tenon by tightening the four 5/16-18 socket head
set screws to min. 1.5ft-lbs (2Nm) to max. 1.8ft-lbs (2.5Nm) with 5/32”
Allen wrench.
•
To adjust the tilt angle of the fixture, loosen the 3/8-16 Socket Cap
Screw in the Knuckle with a 5/16” Allen wrench, rotate fixture to the
desired angle and re-tighten to min. 2.5ft-lbs (3.5Nm) to max. 3ft-lbs
(4Nm). See Figure A.
Figure B
Figure C
color temperature switch
lumen level switch
photocontrol switch
To change settings, use a
3/16” Allen
wrench to remove the switch cover
on the side of the fixture See Figure C. Choose your settings and replace
switch cover. Tighten to min. 1.5ft-lbs (2Nm) to max. 1.8ft-lbs (2.5Nm).
Set Screw
Switch cover
Socket Head
Cap Screw
Photosensor
5.236" [133]
1.772" [45]
0.138" [3.5]
BRACKET THICKNESS
2.000" [50.8]
1.000" [25.4]
Ø0.531" [Ø13.5]
2PLACES
Ø0.687" [Ø17.5]
3
/8
”
-16*1-7/
8"
Socket head cap screw
5/16
“
-1
8*7
/
8"
Socket set screw
3
/8
”
-16
*3/4"
Socket head cap screw
#10
-24
*1/2"
Socket head cap screw
Socket Head
Cap Screw
Socket Head
Set Screw
(4)Socket Head
Cap Screws
