background image

Pulse Output Device

11

Get the latest PDF manual:

https://www.lcmeter.com/resources/technical/manuals

Mobile/online version of this manual:

https://www.lcmeter.com/manuals

Regulatory Compliance Tag Markings

Explosive Atmospheres

·

This equipment has been found to comply with the European Directive for Equipment For
Potentially Explosive Atmospheres 2014/34/EU (ATEX), and Certification Scheme for
Explosive Atmospheres of INTERNATIONAL ELECTROTECHNICAL COMMISSION
(IECEx). Evaluation was made in 2018 by DNV GL to the ATEX Directive with a certificate
number Presafe 18 ATEX 12438X and in 2011 to IECEx scheme with a certificate number
IECEx DNV 11.0012X, where X represents the following Special Conditions for Safe Use:
1) Only Ex d certified cable glands and thread adapters are to be used; and 2) For ambient
temperatures above 70 °C, use field wiring suitable for 20°C above maximum ambient
temperature.

·

II

 – Suitable for use in surface (not mine) installations.

·

2G

 – High level of protection is provided against flammable gases, vapors, or liquids,

which may exist during normal operation.

·

Ex d

 – Explosion protection is provided by a flameproof enclosure.

·

T6

 

·

Gb

 – Equipment group per IEC 60079-0 and EN 60079-0.

·

Safe limits of ambient temperature.

Summary of Contents for POD1

























Reviews: