background image

5

lippert.com 

    432-LIPPERT (432-547-7378)    

 

Rev: 10.13.21

Screen Assist

Installation and Owner’s Manual

(For Aftermarket Applications)

CCD-0004313

5. 

Move the assembly to a stable work surface and 

measure from the ends of the push bar to each mark made 

previously in step 4. 

(Fig. 10A, Fig. 10B)

6. 

Add these measurements together, then divide that 

sum by 2.  Then, using a non-permanent marker make 

new marks on each end of the push bar equal to this new 

number. 

Example:

 If measurement 

(Fig. 10A)

 = 1 

1/2

” and 

measurement 

(Fig. 10B)

 = 3”, adding them equals 4 

1/2

”. 

Then, 4 

1/2

” divided by 2 equals 2 

1/4

”.  Re-apply marks on 

each end of the bar at 2 

1/4

”.

NOTE: 

This centers the push bar between the sleeves, 

ensuring that there is an equal amount of bar for strength 

inside each sleeve.

Fig.11 

measure

measure

marks

Fig.10 

7. 

Slide the sleeves onto each end of the push bar to the 

new marks and, using the supplied screws, fasten the 

sleeves to the push bar. 

(Fig.11)

.  The push bar is now 

complete.

NOTE: 

Ensure that care is taken when measuring and 

fastening the push bar to the sleeves. The screw creates 

a hole in the bar, and once installed, small adjustments 

cannot be made.

Sleeve to Bar Installation (Alternate Method)

NOTE: 

Additional assistance may be needed for this 

method.

1. 

Measure to find center point on the push bar. Mark the 

center point with a non-permanent marker 

(Fig 12)

.

2. 

Slide sleeves over the ends of the push bar 

(Fig.12)

Fig.12 

center mark

 B

B

 X”

 X”

Fig.13 

center

3. 

From inside the screen door, dry fit the assembly to the 

door’s width. Insert the lever side sleeve up to the insertion 

line on the inside push bar lever handle 

(Fig. 13A)

 and align 

the mount bracket on the door hinge side so that the bar 

rests parallel to the frame of the door 

(Fig. 13)

. The sleeve 

mount bracket should be centered vertically on the raised 

portion of the screen door frame 

(Fig. 13)

.

4. 

Adjust the push bar in the sleeves and measure to 

make sure an equal amount of bar (X”) is showing from 

the center mark made in step 1 to the start of the each 

sleeve 

(Fig. 13)

.  This ensures there is an equal amount of 

bar inside each sleeve for strength.  Mark on the bar where 

the sleeves start with a non-permanent marker 

(Fig.13B)

You may need additional assistance to hold the assembly 

in place while the measurements are taken and marks are 

made. 

Parallel

 A

center

 A

B

Summary of Contents for 2021000090













Reviews: