background image

Rev: 12.13.2018

Page 2

CD-0002211

TABLE OF CONTENTS

Introduction

 

2

Safety Information

 

2

Resources Required

 

2

Installation

 

3

Power Supply 

5

Troubleshooting

 

6

Notes

 

7

Introduction

Hotspot™ was designed and engineered for the mobile lifestyle. The weatherproof, externally-mounted 

antenna array increases your signal range far beyond a simple “off-the-shelf” mobile hotspot that can 

lose strength by just moving your device around the campsite. Hotspot™ utilizes Direct Link Technology 

specifically designed for the RV lifestyle. Direct Link Technology provides the fastest 4G LTE connectivity 

available, up to 150Mbps, so you’re connected wherever the road may take you.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) 

This device may not cause harmful interference, and (2) this device must accept any interference received, 

including interference that may cause undesired operation.

Safety Information

Always wear eye protection when performing installation. Other safety equipment to consider would be 

hearing protection, gloves and possibly a full face shield, depending on the nature of the installation.

Resources Required

• Cordless or electric drill or screw gun

• Appropriate drive bits

• Sharp cutting tool

• Tape

• Tape measure

• Silicone sealant

• 16 AWG wire

• Wire nuts

• #8 x 

3/4

" stainless steel pan head scews (12)

Summary of Contents for Hotspot OEM









Reviews: