LinMot E1100 Series Manual Download Page 59

Page: 59 / 62

Page 59 of 62

NTI AG / LinMot

15.13 Error

In this section the Error behaviour can be defined.

15.13.1 Error Detection Mask

With the error detection mask a single error can be disabled. Also a LinRS error causes the MC-SW go to the
error state.

LinRS\ Error\ Error Detection Mask

Checksum Error

(Default Selection On)

End Of Telegram Missing

(Default Selection On)

Wrong Msg Main ID

(Default Selection On)

Wrong Msg Sub ID

(Default Selection On)

UPID Not Existing

(Default Selection On)

15.14 Respond On Msg With Error

Typically the LinMot drive doesn’t answer to wrong telegrams, with this mask the response for certain errors
can be enabled. With turned on Communication state in the MC default response the error will be responded to
the master.

LinRS\ Error\ Respond On Msg With Error

Checksum Error

(Default Selection On)

End Of Telegram Missing

(Default Selection On)

Summary of Contents for E1100 Series































































Search results

Summary of Contents for E1100 Series

Reviews:

Related manuals for E1100 Series

Brands by name

Popular brands

LinMot E1100 Series, Manual

Search results

Summary of Contents for E1100 Series

Reviews:

Related manuals for E1100 Series

Brands by name

Popular brands