background image

 

Linkcom France 

11 rue du Soleil Levant 92140 CLAMART                                                                                     Copyright © 2008 – Linkcom – Tous droit réservés 

12 

 

 

8.3. GSM Gateway status 

The GSM Gate status provides you with all technical information’s corresponding to SIM card in GSM Module 1 and 
GSM module 2. 
 

Frequency Channel:

 GSM network channel number - GSM frequency connected to BTS.  

Channel 0 - 124 are used for GSM 900 and channel 512 - 885 for GSM 1800.  
 

Signal Strength, BCCH strength:

 GSM Signal force (Is related with Antenna position) 

 

o  -113 to -99 dBm: very bad signal - it is impossible to use any GSM network services. 
o  -98 to -83 dBm: bad signal - you can send SMS messages. Since level -87dBm you can establish voice 

connection 

o  -82 to -71 dBm: good signal - you can send SMS messages and make calls. Data transmission CSD is not 

reliable 

o  -70 to -51 dBm: very good signal - you can use all services of GSM network without any restriction. 

 

Country Code, Network Code, Area Code:

 Country Code N°, Provider Network N°, where SIM card is logged 

 

Cell ID:

 BTS number, where GSM module is registered. 

 

IMSI:

 International Mobile Subscriber Identity  

 

GSM Firmware version:

 SW version for GSM part. 

 

 

Summary of Contents for Link Gate SIP














Reviews: