manualshive.com logo in svg

Linkcom Link Door Phone, User Manual, Page: 19 / 31

Share
Download
Linkcom Link Door Phone User Manual Download Page 19

                    All rights are reserved to Linkcom 

 

classe 

DR 

classement 

LinkDoor

 

Number 

001

 

date 

15/04/05

 

page 

19/31

 

 
 

The parameters 81 and 82 will delete all numbers stored in memory table of Group 1/ Day mode and Group 2/Night 
mode. 
The parameters 83 – 85 will execute a selective Main setting only for parameters starting with 3.. – 5.. 

ATTENTION !!!

 the deleting is non-reversible !!!, It is then necessary to program it again. 

2.8  Remote Programming Termination 

Parameter Value 

Meaning 

Main 

Exam.1 Exam.2

9  

E N D of Remote 

programming 

 

 

 

After dialing remotely the digit 9 the Door phone will hung up. 

2.9 System 

Setting 

Parameter Value 

Meaning 

Main 

Exam.1 Exam.2

6# s 

Number of buttons not 

used < 2 

 

 

 

 s = 0 Main module is fitted with 2 buttons as standard 
 s = 1 Main module is fitted with 1 button 
 s = 2 Main module is feeted with no button 
 S0 setting is a factory one, no service can change it and so it is recommended not to change this parameter. 

Note: In remote mode the value of this parameter is checked and if not satisfactory form unknown reasons, so it is set 
up to s = 0 (fitted with 2 buttons). 

Atention !!! This parameter does not mainally affect the correct function of Doorphone. 
 
 

Summary of Contents for Link Door Phone
































Reviews:

No comments